User manual EMERSON FANS WINDJAMMER

[. . . ] READ AND SAVE THESE INSTRUCTIONS ® ® Emerson Ceiling Fans - MODEL CF960 - WINDJAMMERTM Ceiling Fan Owner's Manual Net Weight: Model No. 27. 6 Lbs. CF960CK 00 CF960WB 00 CF960BS 00 LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for thirty years from the date you purchased your ceiling fan. All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. [. . . ] Position the pin through the two Install the clevis pin and secure with the hairpin clip holes in the downrod and align the hanger ball so the (Figure 3). The clevis pin must go through the pin is captured in the groove in the top of the hanger holes in the motor coupling and the holes in the ball. Be sure to push the straight leg of the securely tighten the setscrew in the hanger ball. hairpin clip through the hole near the end of the A loose setscrew could create fan wobble. clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. Be sure the groove in the ball is lined up with tab on the hanger bracket (Figure 7). ! WARNING WARNING Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall. ! To avoid fire or shock, follow all wiring instructions carefully. Any electrical work not described in these instructions should be done or approved by a licensed electrician. WARNING Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard. ! WARNING ! WARNING The fan must be hung with at least 7' of clearance from floor to blades (Figure 6). CEILING To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and hanger bracket. NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY. OUTLET BOX AT LEAST 7' Figure 6 ! FLOOR HANGER BRACKET HANGER BALL/ DOWNROD ASSEMBLY WARNING Figure 8 The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. 5 Wiring Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. ! WARNING THREADED STUD #8 LOCKWASHER KNURLED KNOB CEILING COVER To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation. Figure 10 ! 1. Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply (this may be a bare wire or wire with green colored insulation) (Figure 9). Securely connect the wires using wire connector supplied. BLACK AND BLUE FAN WIRES GROUND WIRE LISTED WIRE CONNECTOR (3) WHITE SUPPLY (NEUTRAL) NOTE: CEILING COVER OMITTED FOR CLARITY. WARNING To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling. Final Assembly of the Ceiling Fan 1. Mount the blade flange to the blade using three 3/16-24 x 5/16" slotted Phillips head screws and three M5 flat washers (supplied) (Figure 11). Repeat this procedure for the remaining five blades. GREEN WIRE (GROUND) FROM HANGER BRACKET GREEN WIRE (GROUND) FROM HANGER BALL WHITE FAN WIRE BLACK SUPPLY (HOT) THREADED STUD (2) 3/16-24 x 5/16" SLOTTED PHILLIPS HEAD SCREW (3) M5 FLAT WASHER (3) BLADE Figure 9 2. Securely connect the fan motor white wire to the supply white (neutral) wire using wire connector supplied (Figure 9). Securely connect the fan motor black wire and blue wire to the supply black (hot) wire using wire connector supplied (Figure 9). After connections have been made, turn leads upward and carefully push leads into the outlet box, with the white and green leads on one side of the outlet box and the black and blue leads on the other side of the outlet box. ! BLADE FLANGE Figure 11 WARNING Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. 2. Install one blade assembly to the motor hub using two 1/4-20 x 1/2" Phillips oval head screws (Figure 12). Screw the two threaded studs (supplied) into the tapped holes in the hanger bracket (Figure 9). Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover (Figure 10). Secure the ceiling cover in place by sliding #8 lockwashers over the threaded studs and installing the two knurled knobs (supplied). [. . . ] Position the light adapter plate over the light fixture mounting plate. The adapter plate switches must be located in the recessed portion of the mounting plate (Figure 15). Align the holes in the adapter plate with the holes in the mounting plate and install four 5/32-32 x 5/16" Phillips flat head screws (supplied) (Figure 22). Cut the speed control switch pull chain to your desired length (optional). [. . . ]