User manual EMERSON FANS MIDWAY II

[. . . ] READ AND SAVE THESE INSTRUCTIONS ® MIDWAY IITM 54" Ceiling Fan Owner's Manual Net Weight: Model No. 23. 8 Lbs. CF929BS 00 CF929WW 00 LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for thirty years from the date you purchased your ceiling fan. Repair and replacement of defective parts on the light fixture housing or electronics (excluding the lamp) for two years from the date of purchase. [. . . ] Be sure both the ceiling cover and the coupler cover are oriented correctly (Figure 3). PIN HANGER BALL SETSCREW COUPLER COVER CLEVIS PIN SETSCREW MOTOR COUPLING CEILING COVER DOWNROD CLEVIS PIN HAIRPIN CLIP Figure 1 2. Align the clevis pin holes in the downrod with the holes in the motor coupling. The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the downrod to make sure the clevis pin is properly installed. ! Figure 3 5. Position the pin through the two holes in the downrod and align the ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble. ! WARNING WARNING It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed (as shown in Figure 2) could result in the fan falling. It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. PIN HANGER BALL SETSCREW DOWNROD DOWNROD HAIRPIN CLIP SETSCREW CLEVIS PIN CEILING COVER Figure 4 Figure 2 MOTOR COUPLING 6. The fan comes with blue, black and white leads that are 80" long. Before installing fan, measure up approximately 6 to 9-inches above top of hanger ball/downrod assembly. Cut off excess leads and strip back insulation 1/2-inch from end of leads. Turn fan assembly upside down in preparation for mounting fan blade assemblies. 3. While pulling up on the downrod, securely tighten the setscrew in the motor coupling (Figure 3). Attach the lower housing assembly to the fan motor using the two key slot holes. NOTE: Make sure wires and terminals are positioned in raised center area of lower housing assembly, and not pinched between fan and light kit. LOWER HOUSING ASSEMBLY The fan must be hung with at least 7' of clearance from floor to blades (Figure 8). CEILING AT LEAST 7' Figure 8 ! FLOOR RAISED CENTER AREA OF LIGHT KIT HOUSING SCREWS (2) KEY SLOT HOLE (2) WARNING The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Figure 7 5 ! WARNING How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Wire your ceiling fan in accordance with the Owner's Manual supplied with the Fan/Light Control. After splices have been made, carefully push splices up into the outlet box. ! To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked acceptable for fan support, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box. [. . . ] To set the level of light brightness, press and hold the LIGHT DIMMER button. The light brightness will continue to increase then decrease while the button is held down. To turn the light ON or OFF, press and release the LIGHT DIMMER button. The light will turn ON at the light level previously set (See Step 4). [. . . ]