User manual EMERSON FANS MARIOL

[. . . ] READ AND SAVE THESE INSTRUCTIONS ® MARIOLTM Ceiling Fan Owner's Manual Net Weight: Model No. 23. 1 Lbs. CF940AB00 CF940AW00 CF940BC00 CF940PW00 CF940SCK00 CF940WB00 LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for thirty years from the date you purchased your ceiling fan. All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. [. . . ] Be sure that the ceiling cover and the coupling cover are both oriented correctly (Figure 3). DOWNROD SETSCREW Figure 1 DOWNROD 2. Unscrew the setscrew (Figure 2) until it clears the inside of the motor coupling. Align the clevis pin holes in the downrod with the holes in the motor coupling. The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the downrod to make sure the clevis pin is properly installed. ! COUPLING COVER Figure 3 5. Position the pin through the two holes in the downrod and align the hanger ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble. ! WARNING WARNING It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed (as shown in Figure 2) could result in the fan falling. It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. HANGER BALL MOTOR COUPLING HAIRPIN CLIP SETSCREW CLEVIS PIN PIN SETSCREW DOWNROD DOWNROD HAIRPIN CLIP CEILING COVER CLEVIS PIN SETSCREW Figure 4 MOTOR COUPLING Figure 2 3. Tighten the setscrew (Figure 2) securely while pulling up on the downrod. NOTE: The setscrew must be properly installed as described above, or fan wobble could result. The fan comes with blue, black and white leads that are 80-inches long. Before installing the fan, measure up approximately 6 to 9-inches above top of hanger ball/downrod assembly. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Engage the connector of the switch housing assembly with the motor connector (Figure 7). The two connectors are keyed and color-coded and must be mated correctly (color-to-color) before they can be engaged. Remove the four mounting screws from the switch housing plate (Figure 7). Position the switch housing assembly on the switch housing plate and secure using the four mounting screws (Figure 8). NOTE: Do not pinch wires between the switch 5 housing assembly and the switch housing plate. The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds. [. . . ] Connect the wood pendant (supplied) to the 3-speed switch pull chain by sliding the wooden pendant (small hole first) onto the pull chain. Attach the chain coupler to the end of the chain and allow the wooden pendant to fall down over the coupling. The use of any other control not specifically approved for this fan could result in fire, shock and personal injury. ! WARNING 7 This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. [. . . ]