User manual EMAGIC A26

[. . . ] Hardware >> Version 1. 2, August 2003 >> English User's Manual Emagic Soft- und Hardware GmbH-- Software License Agreement PLEASE READ THIS SOFTWARE LICENSE AGREEMENT ("LICENSE") BEFORE USING THE SOFTWARE. BY USING THE SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. IF YOU ARE ACCESSING THE SOFTWARE ELECTRONICALLY, SIGNIFY YOUR AGREEMENT TO BE BOUND BY THE TERMS OF THIS LICENSE BY CLICKING THE "AGREE/ACCEPT" BUTTON. IF YOU DO NOT AGREE TO THE TERMS OF THIS LICENSE, RETURN THE EMAGIC SOFTWARE TO THE PLACE WHERE YOU OBTAINED IT FOR A REFUND OR, IF THE SOFTWARE WAS ACCESSED ELECTRONICALLY, CLICK "DISAGREE/DECLINE". [. . . ] It is recommended that you keep your existing file. " · Click the "Yes" button for each of these version conflict boxes. · After a few moments, your installation will have been completed successfully. It is possible that the A26 may need to be re initialized following installation on Windows 98 SE. To do so, simply restart Windows. · · 6. 5 · · · · · · · · · · Installation on Windows 2000 and XP Start and boot your computer completely. Connect the A26 to any of your computer's unused USB ports via the supplied USB cable. Select "Search for a suitable driver for my device (recommended) Click on the "Next" button. If you are installing the driver from CD-ROM, check the CD-ROM drive option. The following message will appear on-screen: "The wizard found a driver for the following device: Emagic A26 A62 m USB Device". Click on the "Next" button. 40 Emagic--A26 6. 5 Installation on Windows 2000 and XP · · · · · · The: "Completing the Found New Hardware Wizard, Emagic A26 A62 m USB Device, Windows has finished installing the software for this device. The hardware you installed will not work until you restart your computer" message will appear. You will be prompted with the following dialog: "You must restart your computer before the new settings will take effect. " Click on the "Yes" button. Your computer will be restarted. On rebooting Windows 2000, The Found New Hardware Wizard will display: "Emagic A26 (WDM)" · This will be followed by the: "Digital Signature Not Found. . . " message. This message is shown as the Emagic A26 drivers currently do not contain a Microsoft digital signature. The Emagic drivers are fully functional, and there is no risk associated with the installation of these drivers on your system. · You will be asked the following: "Do you want to continue the installation?" · Click on the "Yes" button. · During installation you may be asked to insert the Windows 2000 Installation CD-ROM or the Emagic Drivers CD-ROM. Please insert the appropriate media and/or select the correct drive and path from the file selector box, as prompted. · Following these steps, your installation will have been completed successfully. It is possible that the A26 may need to be re-initialized following installation on Windows 2000/XP. To do so, restart Windows 2000/XP. User's Manual 41 6 Installation and Updating 6. 6 Driver Updates This section describes the update procedure for a system with an existing A26 driver installed. If this is the first time you have connected the A26 to your computer, you should refer to the earlier installation section. The A26 must have been previously installed successfully on the system. · · · Insert the A26 Driver Update CD-ROM into your computer's CD-ROM drive, or unpack the updated drivers package to a local drive on your computer, if downloaded from the Internet. [. . . ] Windows Millennium: If the connected digital source uses a sampling rate that is different to that of the A26, resampling occurs in an attempt to match the rate used by the A26. On Windows 98 SE and Windows 2000, there is a technical limitation that affects digital clock input signals. We therefore recommend that the A26 is set to Intern for optimal performance on these operating systems. · · My DAT recorder doesn't recognize the A26's digital signal · The S/PDIF signal carries additional information about the audio material in "Channel Status" messages. This information needs to correspond with the actual sampling rate on some DAT recorders. [. . . ]