User manual ELRO M10B

[. . . ] in the next house, your receiver may be fault triggered by their transmitter. Receiver can only response to RF coding with the same address code setting as its own address code. 1. To adjust address code of Receiver, simply push up one or more of the 5 dip switchlevers. 2. To adjust address code of Control Centre, open the housing of the transmitter unit. [. . . ] MOUNTING THE RECEIVER ONTO THE WALL/JUNCTION BOX: 1. Remove the front cover of the Receiver. (go to step 4 if installed on a junction box) 2. Mark the holes position. 3. Drill two holes and insert the plastic anchors carefully into the holes until they are flush with the wall. 7. Replace the front cover and installation is completed. MOUNTING THE RECEIVER ONTO THE OPTIONAL WALL BOX: 1. Remove the front cover of the Receiver. 3. Drill two holes and insert the plastic anchors carefully into the holes until they are flush with the wall. 4. Pull the wires into the wall box and fasten the wall box onto the wall. 8. Replace the front cover and installation is completed. SL (Off) L SL (On) N - Heat Off - Live - Heat On - Nuetral N L NC COM NO WIRING DIAGRAM FOR 230V APPLICATION The unit is default 230V, you must ad a link between COM & L, follow diagram. It is vital to connect the live into this terminal to avoid overloading of the jump wire. N - Nuetral - Live (230V Feed) - Switched Live N L NC COM NO WIRING DIAGRAM FOR VOLT FREE APPLICATION The unit still requires a 230V feed for V. F. applications L NO COM - Volt Free Feed NC - Normally Closed Most common connexion in Europe. 4. SETTING OF CONTROL CENTRE Heater/Cooler Selection Before making any selection in the control centre, its back housing must be removed as follows: Inside the Control Centre after back housing is removed, you can find the DIP switch. These three switches are used to control the span and heat/cool system. Set the DIP switch (position 3) according to your selection of heater system or cooler system as the following diagram. swtich 3 ON = heater swtich 3 OFF = cooler -3- -4- 5. SETTING PROGRAMS * SELECT WEEK-DAY 1. Press the SET PROGRAM button, the day indicator shows the program day and is flashing. Program number indicator shows the current program for the selected day. You can select the whole week, working day, weekend, or individual day to program. 00 06 12 18 24 00 06 12 18 24 00 06 12 18 24 00 06 12 18 24 00 06 12 18 24 Press the button to toggle the control temperature setting and advance the settinghour digit by one. Hour Digit (Clock) is 2 and the 02 hour bar is flashing and the operation mode for hour 01 is set to economic mode. 5. Press the P button to terminate the setting procedure and to return to normal operation mode. EXAMPLE: P button is pressed. Terminate the setting procedure and the new control profile is : 00 06 12 18 00 06 12 18 24 is on 24 6. The setting procedure will terminate automatically when no button is pressed for 10 seconds. TESTING THE RF TRANSMISSION RANGE 1. Press UP button until the setpoint temperature is higher than room temperature by a few degrees. 4. If the LED is not On, try to place the Control Centre closer to the Receiver. Press Down button to adjust the setpoint temperature to be lower than room temperature to "turn off" the receiver. 6. The receiving range between Control Centre and Receiver is 50M in open area. When placed indoors, this distance may be shorter because of blocking by concrete walls etc, but is enough for most household applications. [. . . ] 3. The unit will revert to normal operation mode automatically when no button is pressed f or 10 seconds. ANTI-FREEZING MODE 1. Pressing the UP and DOWN buttons simultaneously will activate the anti-freezing mode (for heater mode only). The ANTIFREEZING icon and the HAND icon will be turned on while both the COMF and ECON icon will be turned off. 2. Pressing any button will terminate the antifreezing mode and revert to normal operation mode. [. . . ]