User manual ELK PRODUCTS ELK-P412(K)
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ELK PRODUCTS ELK-P412(K). We hope that this ELK PRODUCTS ELK-P412(K) user guide will be useful to you.
Manual abstract: user guide ELK PRODUCTS ELK-P412(K)
Detailed instructions for use are in the User's Guide.
[. . . ] Power Supply
APPLICATION
ELK-P412 ELK-P412K Includes Battery
4 Amp, 12 Volt DC Power Supply & Battery Charger with Enclosure
The ELK-P412 is a general purpose high current power supply and battery charger. [. . . ] Enclosure Dimensions: 12. 5"H x 7. 5"W x 3. 75"D.
Features and Specifications subject to change without notice.
+
POWER ON LEDS
EARTH GROUND AC INPUT DC OUTPUT AC POWER ON LED
NEG +12V OUTPUT 3
BATTERY
LN
LINE NEUTRL GRD
-V +V
NEG +12V OUTPUT 1
NEG +12V OUTPUT 2
DO NOT ADJUST (FACTORY SET)
INSTALLATION / OPERATION
1. Mount enclosure in secure location near an AC power outlet that is not controlled by a switch. (supplied power cord is 6 feet long) 3. Connect devices to be powered to the screw terminals for DC output. The power distribution board has three sets of outputs, each set is limited to 2. 5 amps. If a device requires more that 2. 5 Amps, parallel two sets of terminals. Warning High Voltage is now present at the power supply AC input terminals. The LEDs at the power outputs should be on (if any are off, check for overloaded condition). If AC power is lost, the Low Battery circuit will disconnect the battery if it's voltage drops below 10 Vdc. This helps to prevent "deep discharging" of the battery.
LOAD 1
LOAD 2
120VAC POWER CORD (6')
LOAD 3
BLACK
RED
12 Volt Battery (Included with ELK-P412K)
P. O. [. . . ] The sounder is powered from the Battery.
4 AMP POWER SUPPLY
WARNING SHOCK HAZARD
ELK-967 POW ER DISTRIBUTION MODULE
POWER ON
2. 5 AMP FUSE (PTC)
2. 5 AMP FUSE (PTC)
2. 5 AMP FUSE (PTC)
SW1 POWER OFF
14. 5VDC IN
+
+
OUTPUT 1 UP TO 2. 5 AMPS OUTPUT 2 UP TO 2. 5 AMPS OUTPUT 3 UP TO 2. 5 AMPS
POWER ON LEDS
EARTH GROUND AC INPUT DC OUTPUT AC POWER ON LED
NEG +12V OUTPUT 3
BATTERY
LN
LINE NEUTRL GRD
-V +V
-
+
-
+
-
+
NEG +12V OUTPUT 1
NEG +12V OUTPUT 2
ELK-912 RELAY LOAD 1 LOAD 2
Voltage is lost here during AC Power Failure which will cause the relay to drop out and activate the sounder
N COMNC O
-
+
CONNECT LOADS TO EACH OUTPUT OR COMBINE OUTPUTS TO SUPPLY MORE CURRENT (DO NOT TO EXCEED 4 AMPS TOTAL)
BLACK
RED
12 Volt Battery
12 VOLT SOUNDER
+ [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ELK PRODUCTS ELK-P412(K)
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ELK PRODUCTS ELK-P412(K) will begin.