User manual ELK PRODUCTS ELK-ML8
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ELK PRODUCTS ELK-ML8. We hope that this ELK PRODUCTS ELK-ML8 user guide will be useful to you.
Manual abstract: user guide ELK PRODUCTS ELK-ML8
Detailed instructions for use are in the User's Guide.
[. . . ] * Try these other fine ELK products * M1 Cross Platform Control M1 (Std) Integrates Security, Lighting, Telephone, and Energy Management. M1G (Gold) More powerful version of M1 with more expansion and capabilities. [. . . ] · Operating Power Derived From the Magic Module
Power Source or the Caddx Control.
· Operating Voltage: 9. 6-15 Volts D. C. · Current Required: 30mA.
REQUIRED EQUIPMENT: (not included)
· ELK Magic Module (ELK-MM443). · ELK Programming Kit (ELK-MK485).
Features and Specifications subject to change without notice.
828-397-4200 Voice 828-397-4415 Fax http://www. elkproducts. com email: info@elkproducts. com PO Box 100 · Hwy. 70W · Hildebran, NC 28637 · USA
Instructions Printed On Inside
The Link Interface (ELK-ML8) connects to the data bus of the Caddx NX Control¹ using only 2 wires. Changes to these flags are broadcasted over the Magic Module data bus. In addition, 240 bits of data from the Control may be interrogated on demand by the Magic Module. In order to program the 16 collection flags or develop a Home Control or Automation application, a Magic Module Programmers Kit (ELK-MK485) is needed.
INSTALLATION
Step 1. Disconnect all power to the Caddx NX Security Control and the ELK Magic Module. Mount the Link Interface using the enclosed self adhesive foam tape or two of the special NX enclosure slide rails. Connect the Link Interface, Caddx NX Control, and Magic Module as per figure 1 below. NOTE: Figure 1 shows the Magic Module components powered from the NX Control. Be certain that the maximum combined current draw including any keypads or auxiliary devices does not exceed the ratings published with the control. [. . . ] XMIT RCV STATUS PWR = = = = Blinks when information is being transmitted to or received from a Magic Module Blinks when the NX Control is transmitting information to the Link Interface Blinks slowly when the Control Keypad data bus is operational. On when the Link Interface is receiving Power.
LEDs
¹ Works with most Caddx NX Controls except "E" series
* CADDX NX4/6/8 ALARM CONTROL
LINK INTERFACE ELK-ML8
JP1 MODE
Leave in the NORMAL Position D5 not used
Mount the ELK-ML8 Interface Here Or Mount using Rails Here
DATA NEG +V
AUX NORMAL
+12V A B NEG J1
XMIT RCV STATUS PWR
+V NEG DATA
TO CADDX KEYPAD BUS (3 WIRES)
RED GREEN RS-485 BUS (4 WIRES)
BLACK YELLOW See Step 3 for +V Optional Hookup
NEG B DATA A DATA +12 VOLTS
KP DATA KP COM KP POS
CADDX NX ALARM CONTROL BOARD
* ELK-MM443 MAGIC MODULE
1 2 4 8 16 J1 SELECT X-10 2-WAY 1-WAY JP10 POWER J3 X-10 and DALLAS Interface J5 RELAY 4 IN OUT RELAY 3 IN OUT
* OPTIONAL POWER SUPPLY ELK-P1216
DATA BUS ADDRESS JUMPERS SET TO ADDRESS 1
JP1
JP2
JP3
JP4
K1
K2
K3
K4
+
AB
J2 1
See Step 3 for +V Optional Hookup
-
2
3
-
4
NO COM NCNO COM NCNOCOM NCNO COM NC RELAY 3 RELAY 4 RELAY 1 RELAY 2
* X-10 Items noted with * must be purchased separately
2 WAY POWERLINE INTERFACE MODEL:PSC05
Required only for Applications using X-10 Devices
Figure 1. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ELK PRODUCTS ELK-ML8
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ELK PRODUCTS ELK-ML8 will begin.