User manual ELK PRODUCTS ELK-110

[. . . ] OVERVIEW The ELK-110 offers high quality pre-recorded voice messages and 3 alarm sounds, warble siren, pulsing buzzer, and temporal coded bell. It features two (2) input channels, one for Burglary, and one for Fire. It is possible to select voice only, siren only, or combined alternating playback. [. . . ] Tone, Fire, fire, leave immediately Followed by a Temporal Coded Bell sound. Switch & Jumper Options: SW1 SW2 SW3 Closed Open Closed Open Closed Open Warble Siren Sound. Cutting this jumper deletes the voice message on the BA Burglar channel input. . Cutting this jumper deletes the voice and Temporal Coded Bell sound on the Fire channel input, leaving a buzzer or warble. Note: ComboTrigger on +BA or -BA will still play the " Fire" message and Temporal Coded Bell. Cutting this jumper deletes the siren and Temporal Coded Bell sounds from both the Burglar and Fire channels. For Spanish Only, cut the foil jumper marked "Cut Spanish Only" located on the back of the circuit board and then open switch SW2. = = = = = = Voice Driver ELK-110 With Temporal Coded Bell APPLICATION: The ELK-110 is the first voice siren driver to include a Temporal Coded Bell Sound, which meets the ANSI standard for emergency evacuation signaling. The ELK-110 is ideal for residential and commercial alarm jobs and features two input channels, bilingual voices messages, and many unique options. Voice Driver ELK-110 Version 4. 0 With Temporal Coded Bell FEATURES: · Two Input Channels, Burglar & Fire. · Temporal Coded Bell - ANSI standard Audible Emergency Evacuation Signaling. · MilliMiserTM - option reduces current draw for controls with limited alarm output power · ComboTriggerTM - option for single alarm output controls which have the option of steady for burglar and pulsing for fire. · VolumeStepTM - option starts the siren sound at low volume and gradually increases the volume to maximum over a 90 second time period. · Lifetime Limited Warranty, call for details. SPECIFICATIONS: SW4 JP1 JP2 · Nominal Operating Voltage: 10-14 Volts D. C. · Size: 2. 75" X 4. 0" (70mm X 102mm). Features or Specifications subject to change without notice. JP3 Note: 828-397-4200 Voice 828-397-4415 Fax http://www. elkproducts. com email: info@elkproducts. com PO Box 100 · Hwy. 70W · Hildebran, NC 28637 · USA Instructions Printed On Inside 05/02 ELK-110 INSTALLATION INSTRUCTIONS NEG: Connect this wire to a common negative (-) terminal on the control panel or power source. NOTE: The Fire and +BA inputs draw the maximum current unless the +12V wire is connected as explained below. BLACK SIREN ONLY ON BURG: Cutting JP1 deletes the "Intruder" message on the +BA or -BA (Burg) inputs. Note: This also deletes the ComboTrigger feature which is the detection of pulsing voltages. SIREN ONLY ON FIRE: Cutting JP2 deletes the "Fire" message on the FIRE input. [. . . ] Caddx, Napco, Ademco i. e DSC 832 Two 8 Ohm Speakers in Series (16 ohm load) A constant positive voltage from the alarm output(+Bell) to Yellow Wire(+BA) input will play the burglar message, while a pulsing positive voltage will play the fire message. (Pulsing requires connection of RED wire to +12 Volts DC. ) Security Control Power Output Terminals A constant alarm output(pull to ground Neg) from -Bell to the Blue Wire(-BA) input will play the burglar message, while a pulsing output will play the fire message. Requires connection of RED wire to +Bell or +Aux @ 2 Amps Min. Security Control ELK-110 Power Output Terminals ELK-110 NEG BLACK - Aux (Neg) NEG BLACK - Aux (Neg) + Aux (+12V) Alarm Output Terminals Two 8 Ohm Speakers in Parallel (4 ohm load) Two 8 Ohm Speakers in Series, One in Parallel (6 ohm load) This speaker will be louder FIRE not used + Aux (+12V) FIRE not used +BA YELLOW Alarm Output Terminals +BA not used SPKR SPKR SPKR SPKR -BA RED not used - Bell or Neg -BA BLUE - Bell + Bell +12V RED + Bell or +Alarm +12V optional required [. . . ]