User manual ELECTRO-VOICE XI-A

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ELECTRO-VOICE XI-A. We hope that this ELECTRO-VOICE XI-A user guide will be useful to you.


ELECTRO-VOICE XI-A : Download the complete user guide (611 Ko)

Manual abstract: user guide ELECTRO-VOICE XI-A

Detailed instructions for use are in the User's Guide.

[. . . ] Xi-A Series Loudspeaker System Flying Manual ELECTRO-VOICE® Xi-A Rigging Manual Table of Contents 0. Rigging-Safety Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. 1 The Flying Xi-A Loudspeaker Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To align the top-rear corner of an Xi-A cabinet with the bottom-rear corner of an Xi-A cabinet above it, the rigging straps at the bottom of the upper cabinet are shifted along the rigging track until the rear corners of the adjacent cabinets are in alignment. A number of examples are presented in the following section that will demonstrate both the mechanical and acoustical aspects of an array design with the Xi-A loudspeaker systems. 2. 3. 2 Practical Considerations The vertical angle of the flying Xi-A loudspeaker system may be adjusted by choosing different positions of attachment along the rigging track on the cabinet. There are a number of attachment points allowing for a wide variety of angles. Although the center of gravity is slightly different for each of the systems, the balancing concept is the same. The further the top attachment point is towards the back of the cabinet, the greater the downward angle, as shown in Figure 2. 5. As the attachment point is moved forward, the cabinet will have less downward angle and, at the furthest point forward, will have an upward tilt. This principle holds true when hanging any of the Xi-A systems in either rigging orientation (rigging track on the top and bottom, or on the sides). Vertical arrays are constructed by hanging Xi-A systems from one another in succession. Both the curvature of the array and the angles of the individual cabinets are controlled by the rigging attachment positions. The shape of the array curve is determined by the position on the lower track of an already hanging cabinet from which the next cabinet is hung, the further back the attachment point is on the upper box, the further back the lower cabinet is shifted and, hence, the greater the curvature of the array. The goal is to have the back, top and bottom edges to adjacent cabinets in alignment. In Figure 2. 6a, one Xi-A enclosure is hung so that it points straight ahead and a second is added below. The addition of the second enclosure causes the top cabinet to point upward. Shifting the upper attachment point of the first cabinet back, as shown in Figure 2. 6b, counteracts the additional load and results in the upper cabinet pointing straight ahead ELECTRO-VOICE® Xi-A Rigging Manual 8 again. Note that this change has no affect on the angle of the lower cabinet. Additional Xi-A enclosures may be hung in succession in this fashion, creating a tall vertical line array (as long as the working-load limit of all of the mechanical components are not exceeded and a sufficient safety factor is maintained throughout the array). With the Xi-A loudspeaker systems oriented with the rigging track on the top and bottom of the cabinets, a short rigging strap is used between the cabinets to minimize the spacing between the systems. If, however, Xi-A enclosures having different dimensions are hung from one another (an Xi-1122A suspended beneath an Xi-1191AF, for example), a longer strap would be required to accommodate the different distances In width between the rigging tracks. Another option would be to use two RS-1B double-stud swivel-ring fittings linked with a threaded-chain connector or a carabineer snap hook. (The RS-2B single-stud-ring fittings could be used in lighter-weight applications. ) With the Xi-A loudspeaker systems oriented with the rigging track on the sides at the cabinets, a longer rigging strap is required between the cabinets to minimize the spacing between the systems. If, however, Xi-A enclosures having different dimensions are hung from one another (an Xi-1122A suspended beneath an Xi-1191AF, for example), a longer strap would be required to accommodate the different distances in width between the rigging tracks. [. . . ] Box 1907 Big Bear Lake, CA 92315, USA (909) 878-9104 www. smirigging. com smiller@smirigging. com Custom Rigging Strap Assemblies: Custom wire rope or webbing rigging strap assemblies that use the RS-1B and RS-2B fittings may be ordered from: Sound Manufacturing, Inc. Box 1907 Big Bear Lake, CA 92315, USA (909) 878-9104 www. smirigging. com smiller@smirigging. com General Rigging Supplies: A wide variety of standard and specialty rigging hardware components for both touring and permanent-installation applications are available from: Sound Manufacturing, Inc. Box 1907 Big Bear Lake, CA 92315, USA (909) 878-9104 www. smirigging. com smiller@smirigging. com ATM Fly-wareTM 21000 S. Carson, CA 90810 USA (310) 834-5914 www. atmflyware. com clientservice@atmflyware. com 17 ELECTRO-VOICE® Xi-A Rigging Manual Appendix B B. 1 Acoustical References A brief list of references covering the topics of acoustics and sound-system design is presented below: (1) D. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ELECTRO-VOICE XI-A




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ELECTRO-VOICE XI-A will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.