User manual ELECTRO-VOICE EVID

[. . . ] Owner's Manual Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Step 2 - Select Wattage Tap (Models 4. 2t and 6. 2t Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Step 3 - Mount the Speaker to the SAMTM Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Step 5 - Secure the Seismic Tab Connection Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Insert one of the 3/8-16-thread Phillips-head screws through the remaining clip and keep it within arm's reach. Lift the enclosure up to the ceiling and bring its back into contact with the bracket rungs. Slide the enclosure sideways to engage the clip over one bracket rung (1) and, while holding it tight against both rungs, insert the 3/8-16thread screw with its clip into the remaining mounting hole so the clip engages the remaining bracket rung (2, 3). It will slide down the rungs until the four rubber feet are snug against the wall. Using a #3 right-angle Phillips screwdriver, securely tighten the second Phillips-head screw. Gently rotate the EV® logo a quarter turn and press firmly at its center to seat it securely into its mounting hole. 10. Step 4: Mount the Speaker to the Bracket First remove the two Phillips-head screws on the rear of the enclosure. Use the supplied eyebolt to mount one mounting clip to the top of the speaker as shown in Figure 24. Check to make sure that the wiring connections to the amplifier and the satellite speakers are correct and secure. For corner mounting Attach the four rubber mounting feet to the front side edges, and secure the safety line to the eyebolt. Lift the enclosure up to the ceiling and center it back it into the corner until it touches the bracket rungs, then carefully lower it so the top clip hooks over the top rung of the bracket (1). Insert one of the 3/8-16-thread Phillips-head screws through the remaining clip and, with the clip pointing up, thread the screw finger-tight into the lower mtg. Level the clip and tighten securely with a #3 right-angle Phillips screwdriver. EVIDTM Owner's Manual 9 Product Description Rigging cables 1 Rungs 2 3 L angle Eyebolts Ceiling tile This side towards wall Acoustic port Figure 25: Midwall Mounting Figure 26: Attach L-Angles to Speaker Mounting through a suspended ceiling grid On the rear of the enclosure install and tighten two 3/8-16-thread forged steel eyebolts (one is included) with a 3/8" flat washer under each. Cut two pieces of ordinary drop ceiling L angle (wall track) 23 3/4" long and screw them to the top and bottom of the enclosure with 3/4"lomg sheet metal screws, as shown in Figure 26. Connect all the wires and suspend the enclosure, face down, by the eyebolts in accordance with accepted safe rigging practice. Adjust the length of the rigging cables so the tips of the installed L angles just rest on the ceiling cross-tees. It is the installer's responsibility to assure that the chosen rigging points are strong enough to support the load. Warning: Never try to install this speaker in a suspended ceiling without proper rigging support! Step 5: Test System Operation After all connections are made test the complete system operation. 14 contains a troubleshooting guide to assist in locating a variety of speaker related problems. Safety Agency Compliance The EVIDTM 12. 1 bracket system has successfully passed EIA 636 at a safety factor of 8:1. Never set anything on, or hang anything from, the EVIDTM 12. 1 enclosure when using this bracket. For a copy of the model-specific CE Declaration of Conformity, contact ElectroVoice at the address listed at the end of this manual. Maintenance Your EVIDTM system has been designed and manufactured to provide years of durability and reliable service. Never use solvents or harsh cleaning agents of any kind. Floor Mounting The EVIDTM 12. 1 may be placed directly on the floor in a corner or on its side along a straight wall by simply attaching the four rubber mounting feet to the side that will sit on the floor. 10 EVIDTM Owner's Manual Uniform Limited Warranty Electro-Voice® products are guaranteed against malfunction due to defects in materials or workmanship for a specified period, as noted in the individual productline statement(s) below, or in the individual product data sheet or owner's manual, beginning with the date of original purchase. [. . . ] If the grille is rolled or brush painted, the mesh may become clogged with paint and poor sound quality may result. Painting Process (12. 1 Subwoofer) · Remove the four screws securing the front hatch and lift off the hatch panel. · The foam grille blocks are held in place by sharp pins protruding through the baffle board. Note the relative position of the foam and carefully lift the blocks off the pins. Mask around the input panel with tape and tape a piece of heavy paper over the woofer. [. . . ]