User manual ELECTRO-VOICE 602F DATASHEET

[. . . ] The display will return to the main operating screen with the clearest channel in the clearest group assigned. With the transmitter and receiver on, monitor the 602F Receiver main display screen. The AF Bar should show very little if any, indication until you talk or sing into the microphone. On the transmitter, press Set and Down buttons at the same time twice to access the gain adjustment mode. [. . . ] To engage Change Lock press and hold the UP and DOWN arrow keys together until SECURE appears in the display. To remove the Change Lock, press and hold the UP and DOWN keys until ACCESS appears in the display. With the transmitter and receiver on and matching Group and Channel, the main receiver display should be indicating an RF signal on the bar graph. Speak into the microphone and the Audio Meter bar graph should indicate audio signal presence. If the level meters do not show reception, make certain the group and channel are matching and refer to the trouble shooting section. Go back to Section 3. 1 - Receiver Setup & Operation Step 10 to complete system set up and test. -11- 3. 4 Bodypack Transmitter 602F-BP ENGLISH Figure 11 Control View Figure 10 Bodypack Transmitter Figure 12 Top View 7 OR Figure 13 Belt Clip Attachment Rev-BP Controls, Connectors, and Indicators 1. Antenna - Flexible 1/4 wave antenna removable (replacement part - see Section 10) Power On/Off Switch Low Battery LED Indicator TA4 Audio Connector 8. LCD Display (Channel or Frequency, Battery Level Indication) Display Control Buttons (SET/Up/Down) Belt Clip (Removable and Detachable, Flat or Cell Phone Style Clip) 9V Battery Compartment -12- Bodypack Transmitter 602F-BP A. See the accessories section at the end of this manual for optional antennas. (Note: the 602F-BP unique design allows the battery to be inserted and used regardless of the positive and negative terminal position, the indicators are there for reference only). Turning the transmitter On - With battery compartment still open, turn the unit on with Power switch on the top panel. To remove the lock, press and hold SET, UP and DOWN again at the same time until ON-OFF appears in the display. The ON-LOCK mode can also be entered by quickly cycling the power switch three times. But using this method the unit will not be in ON-LOCK the next time it is powered up. To engage Change Lock press and hold the UP and DOWN arrow keys together until SECURE appears in the display. To remove the Change Lock, press and hold the UP and DOWN keys until ACCESS appears in the display. With the transmitter and receiver on and matching Group and Channel, the main receiver display should be indicating an RF signal on the bar graph. Speak into the microphone and the Audio Meter bar graph should indicate audio signal presence. If the level meters do not show reception, make certain the group and channel are matching and refer to the trouble shooting section. Go back to Section 3. 1 - Receiver Setup & Operation Step 1) to complete system set up and test. -13- 3. 5 Bodypack Transmitter 602F-WT ENGLISH Control View Bodypack Transmitter Top View Belt Clip Attachment 602F-WT Controls, Connectors, and Indicators 1. LCD Display (Channel or Frequency, Battery Level Indication) -14antenna removable 6. Belt Clip (Removable and Detachable, Flat or Cell Phone Style Clip) 8. [. . . ] . Pin 1: Ground; Pin 2: Mic Input; Pin 3: +5V bias; Pin 4: +5V bias through a 3000 Ohm resistor Audio Gain Adjustment . . Handheld 27 dB in 3dB steps Bodypack 42 dB in 3dB steps Power Requirements . D 87 mm H x 60 mm W x 20. 4 mm D -29- Section 9 - Approval Information ENGLISH FCC AND INDUSTRY CANADA APPROVAL INFORMATION The Electro-Voice/Telex Transmitters are Type Accepted under United States Federal Communications Commission CFR 47, Part 74 and Industry Canada RSS123. The Electro-Voice/Telex Receivers are approved under United States Federal Communications Commission CFR 47, Part 15 and Industry Canada RSS210. [. . . ]