User manual EIZO RAPTOR 2500 RAPTOR OPENWINDOWS FOR SOLARIS INSTALLATION AND REFERENCE MANUAL

[. . . ] Raptor OpenWindows for Solaris Installation and Reference Manual Publication: 65-0228-01 Copyright © 2005 Tech Source, Inc. Altamonte Springs, FL 32701 (407) 262-7100 Rev F May 6, 2005 Addendum Information Date Released Changes made to: REVISION NUMBER A B C D E F CHANGES DATE May 6, 2005 Initial Release Raptor 2500 Support Added T-Class Cards Integrated MOX on T & I-Class Cards Raptor 2500T Support and Solaris 2. 5. 1 Support Added Raptor 2500T-DL 07-02-01 01-10-02 09-27-02 05-14-03 02-05-04 05-06-05 The Tech Source logo, and Tech Source Raptor are trademarks of Tech Source, Inc. SPARC and UltraSPARC are registered trademarks of SPARC International, Inc. Products bearing SPARC trademarks are based on an architecture developed by Sun Microsystems, Inc. [. . . ] For example, if the Raptor is located in slot 3, and a secondary framebuffer is located in slot 1, then update the pcia-probelist so that slot 3 is probed BEFORE slot 1. A possible configuration may resemble the following: ok setenv pcia-probe-list 3, 2, 1, 4 ok reset-all Once the system is reset, all console messages will be directed to the Raptor card. 3-9 Raptor OpenWindows for Solaris Installation and Reference Manual This page intentionally left blank. 3-10 Chapter 4 SOFTWARE INSTALLATION FOR T-CLASS CARDS 4. 1 Overview This Chapter describes how to install and configure T -Class Raptor cards. The following is a list of T-Class cards: · · · · Raptor Raptor Raptor Raptor 2100T 1100T 2500T 2500T-DL NOTE: This software must be installed on your system prior to running OpenWindows on these cards. The software for the T-Class cards is provided on CD-ROM or by FTP and is composed of the following packages: · · TSItrz. u TSItrzw Device drivers for the Raptor T-Class cards. OpenWindows DDX for the Raptor T -Class cards. 4. 2 Requirements installing the Raptor The following are prerequisites for OpenWindows for Solaris Software: · · The system is running Solaris 2. 5. 1 or higher. OpenWindows Version 3. 5 or higher has already been installed on the system. 4-1 Raptor OpenWindows for Solaris Installation and Reference Manual · · At least 2MB of disk space is available in /usr and /. One or more of the cards listed in Section 4. 1 are presently installed in the system. 4. 3 Installing T -Class Card Driver Software The following are step-by-step instructions for installing the Raptor OpenWindows for Solaris Software from a CD-ROM. Boot the computer w the -r (reconfiguration) option ith by performing the following steps: · · Power ON the computer. Wait until you see boot messages displaying on the screen, then press and hold the Stop (L1) key, and then press the A key. 4. After Insert the CD-ROM labeled "Raptor OpenWindows for Solaris" into the drive. Change directories to the CDROM by typing the following: prompt# cd /cdrom/cdrom0/T-Class 5. 4-2 Chapter 4 ­ Software Installation for T-Class Cards If /cdrom/cdrom0 does not exist, mount the CD-ROM by typing the following: prompt# mount -F hsfs -O -o ro \ /dev/dsk/c0t6d0s0 /cdrom prompt# cd /cdrom/T-Class 6. To install the software, type: prompt# . /install_all This script will ask you a number of yes-or-no questions (generated by Sun's pkgadd installation program). If you did not install the MOX module and libraries in Chapter 3, you can install them now by typing: prompt# cd /cdrom/cdrom0/mox or prompt# cd /cdrom/mox [if the CD-ROM was mounted as outlined in Step 5 above] prompt# pkgadd ­d . TSImox Note: You must install the MOX package in order to use the MOX extension. Reboot the system to complete the installation. One new device name is created in the /dev/fbs directory for each Raptor card. It is denoted by rap1kt# for the Raptor 1100T, rap2kt# for the Raptor 2100T, and raptfp# for the Raptor 2500T and Raptor 2500T-DL (where # represents an instance number assigned by the operating system). 4-3 Raptor OpenWindows for Solaris Installation and Reference Manual 4. 4 Changing Resolution and Bit-Depths 4. 4. 1 Raptor 1100T The default resolution of the Raptor 1100T is set to 1280x1024. The resolution of this card can be changed through the trzconfig utility. Refer to Section 4. 5 for details on using trzconfig. 4. 4. 2 Raptor 2100T The resolution of the Raptor 2100T is fixed at 2048x2048. Refer to Section 4. 5 for details. 4. 4. 3 Raptor 2500T and Raptor 2500T-DL The Raptor 2500T and Raptor 2500T-DL are configured in hardware to support either 2048x2048 or 2560x2048 resolutions. [. . . ] NOTE: To obtain the timing parameters required to use the video-timing method, please contact Tech Source with your monitor's requirements. A. 5 Troubleshooting Problem: The Video-Mode method described in Appendix A was used to change the console resolution but the card does not come up in the desired resolution. Possible Cause: The output-device environment variable may have been set at the ok prompt, or the video-timing variable may be set in NVRAM. The resolution specified by the output-device variable and the video-timing variable takes precedence over the resolution specified by the video-mode variable. If a resolution has not been specified by any of these variables, then the card's default resolution is used. [. . . ]