User manual EIZO FORIS FX2431

[. . . ] Important Please read PRECAUTIONS, this User's Manual and Setup Manual (separate volume) carefully to familiarize yourself with safe and effective usage. · Please read the Setup Manual (separate volume) · The latest User's Manual is available for download from our site: http://www. eizo. com Using the special functions, such as screen size change (ex. changing the horizontal and vertical ratio of images input) for commercial purposes or for the purpose of showing in public may violate copyright laws. Confirm the specification in the manual written in language of the region of purchase. Copyright© 2009 EIZO NANAO CORPORATION All rights reserved. [. . . ] ­ When you feel the image is dark even if the brightness is set to 100. ­ When you feel the image is bright even if the brightness is set to 0. (Set the contrast to lower than 50). Attention Toadjustthecolorsaturation[Saturation] This function allows you to adjust the saturation of the color on the monitor. Adjustable range: -50 to 50 (1) Choose [Color] in the Setting menu and press . (2) Choose [Saturation] in the [Color] menu and press The [Saturation] adjustment menu appears. The adjustment is completed. · This function does not enable to display every color gradation. . . (3) Adjust the saturation of the color with t or u, and then press 8 Chapter 3 Settings and Adjustments Toadjustthehue[Hue] This function allows you to adjust the hue. Adjustable range: -50 to 50 (1) Choose [Color] in the Setting menu and press (2) Choose [Hue] in the [Color] menu and press The [Hue] adjustment menu appears. The adjustment is completed. Attention · This function does not enable to display every color gradation. . . (3) Adjust the hue with t or u, and then press Toadjustthecolortemperature[Temperature] The color temperature can be adjusted. The color temperature is normally used to express the hue of "White" and/or "Black" by a numerical value. In the same way as the flame temperature, the image on the monitor is displayed reddish if the color temperature is low and is bluish if the color temperature is high. The gain preset values are set for each color temperature setting value. 5000K 6500K The white color image is displayed reddish. The white color image is displayed slightly bluish white. NOTE · [Gain] allows you to perform more advanced adjustment (See "To adjust the gain value [Gain]" on page 31). · If you set to "Off", the image is displayed in the preset color of the monitor (Gain: 100 for each RGB). · When changing the gain value, the color temperature adjusting range is changed to "Off". 9300K Adjustable range: Off, 4000K-10000K (specified by every 500K unit, including 9300K) (1) Choose [Color] in the Setting menu and press . (2) Choose [Temperature] in the [Color] menu and press The [Temperature] adjustment menu appears. . (3) Adjust the color temperature with t or u, and then press Tochangethesettingofautomaticbrightnessadjustment function[AutoEcoView] The screen brightness is automatically adjusted corresponding to both the brightness of the image and the environmental brightness detected by the sensor at the lower side of the monitor. Adjustable range: Standard, High, Disable (1) Choose [Color] in the Setting menu and press . (3) Choose [Auto EcoView] in the [Advanced Settings] menu and press The [Auto EcoView] setting menu appears. NOTE · You cannot adjust the value if the function is not displayed, depending on the color mode selected. (See "Adjustment items in each mode" on page 27. ) · Do not cover the sensor. · Set to "High" if you feel a little brighter with "Standard" setting status. . [. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ]