User manual EIZO FLEXSCAN T965

[. . . ] Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2001 by EIZO NANAO CORPORATION. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of Eizo Nanao Corporation. Eizo Nanao Corporation is under no obligation to hold any submitted material or information confidential unless prior arrangements are made pursuant to Eizo Nanao Corporation's receipt of said information. [. . . ] When connecting to a USB compliant PC or another hub, the monitor functions as a hub to which the USB compliant peripherals can be easily connected. As an added advantage, the monitor can be controlled from a PC with a mouse or keyboard when utilizing the enclosed utility software "ScreenManager Pro for USB". Required system environment · PC equipped with USB ports or another USB hub connected to the USB compliant PC · Windows 98/Me/2000 // Mac OS 8. 5. 1 or later · USB cable · The USB hub function may not work properly depending on the PC, OS or peripherals. · When the monitor is not on, the peripherals connected to the downstream ports will not operate. · Even if the monitor is in a power saving mode, the devices connected to the monitor's USB ports (both the upstream and the downstream) will function. Connecting to the USB HUB (Setting up the USB function) · Do not connect the downstream port of the monitor to any peripherals until finishing the USB function. · The followings are procedures for the Windows 98/Me/2000 and Mac OS. 1. 2. Connect the monitor to the PC with the signal cable (See page 10) first, then turn on the PC. Connect the upstream port of the monitor to the downstream port of the USB compliant PC or another hub by using the USB cable . Upstream port: Connect the USB compliant PC or another hub using the USB cable. After connecting the USB cable, the USB function can be set up automatically. 20 4. MAKING USE OF USB (Universal Serial Bus) 3. After setting up, the monitor's USB hub is available for connecting USB compliant peripherals to the downstream ports of the monitor. (Connection example) ENGLISH Scanner USB Cable Printer Monitor Digital Camera PC Keyboard Mouse <Front port> <Rear port> Downstream connector Downstream ports: Connect the cables from USB compliant peripherals such as a mouse, keyboard, etc. ScreenManager Pro for USB (for Windows) For further details about the "ScreenManager Pro for USB", refer to the readme. txt in the CD-ROM. 4. TROUBLESHOOTING If a problem persists even after applying the suggested remedies, contact an EIZO dealer. *The bracket < > indicates the function of ScreenManager Problems 1. No picture · Indicator status: Off Points to check with possible solutions Check that the power cord is correctly connected. If the problem persists, turn off the monitor power for a few minutes, then turn it back on and try again. 18) Try pressing the AUTO/FINE MODE button or control pad or turning the monitor off and then on. 18) These messages appear when the signal is not inputted correctly, even if the monitor functions properly. When the image is displayed correctly after a short time, it is not a monitor's problem. Check that the signal cable is properly connected to the PC and graphics card. Switch the signal input by pressing the BNC/D-Sub selection button on the front control panel. Use the graphics board's utility software to change the frequency setting. (Refer to the manual of the graphics board). · Indicator status: Green · Indicator status: Flashing Green / Yellow · Indicator status: Flashing Yellow 2. ·"No signal detected" error message appears. ·"Out of range" error message appears. Whenever an error signal message appears, the signal frequency will be displayed in red. [. . . ] It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e. g. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. [. . . ]