User manual EIZO FLEXSCAN T766

[. . . ] User's Manual FlexScan T766 Color Display Monitor Important , Please read this User's Manual carefully to familiarize yourself with safe and effective usage procedures. Please retain this manual for future reference. English SAFETY SYMBOLS This manual uses the safety symbols below. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2002 by EIZO NANAO CORPORATION. [. . . ] MAKING USE OF USB (Universal Serial Bus) This monitor provides a hub which supports the USB standard. When connecting to a USB compliant PC or another hub, the monitor functions as a hub to which the USB compliant peripherals can be easily connected. Required system environment · PC equipped with USB ports or another USB hub connected to the USB compliant PC · Windows 98/2000/XP // Mac OS 8. 5. 1 or later · EIZO USB Cable (MD-C93) NOTE · The USB hub function may not work properly depending on the PC, OS or peripherals. · When the monitor is not on, the peripherals connected to the downstream ports will not operate. · Even if the monitor is in a power saving mode, the devices connected to the monitor's USB ports (both the upstream and the downstream) will function. · The followings are procedures for the Windows 98/Me/2000/XP and Mac OS. Connecting to the USB HUB 1. 2. Connect the monitor to the PC with the signal cable (See page 11) first, then turn on the PC. Connect the upstream port of the monitor to the downstream port of the USB compliant PC or another hub by using the USB cable. Upstream port: Upstream Ports To Downstream Ports of the PC or Another Hub Connect the USB compliant PC or another hub using the USB cable. After connecting the USB cable, the USB function can be set up automatically. 4. MAKING USE OF USB (Universal Serial Bus) 21 English 3. After setting up, the monitor's USB hub is available for connecting USB compliant peripherals to the downstream ports of the monitor. Connecting Examples Digital Camera Scanner Monitor PC Keyboard Mouse Printer <Rear port> <Front port> Digital Camera etc. Downstream Port (with a drop down access lid) Downstream Ports Keyboard Printer e Scanner etc. Downstream ports: Connect the cables from USB compliant peripherals such as a mouse, keyboard, etc. The software in the EIZO CRT Utility Disk For information on the software, refer to the readme. txt in the EIZO CRT Utility Disk. 22 4. TROUBLESHOOTING If a problem persists even after applying the suggested remedies, contact an EIZO dealer. *The bracket < > indicates the function of ScreenManager Problems 1. No picture · Indicator status: Off Points to check with possible solutions Check that the power cord is correctly connected. If the problem persists, turn off the monitor power for a few minutes, then turn it back on and try again. 18) Try pressing the AUTO/FINE MODE button or control pad or turn the monitor off and then on. 19) These messages appear when the signal is not input correctly, even if the monitor functions properly. When the image is displayed correctly after a short time, it is not a monitor's problem. Check that the signal cable is properly connected to the PC or graphics board. Switch the signal input by pressing the BNC/D-Sub selection button on the front control panel. Use the graphics board's utility software to change the frequency setting. (Refer to the manual of the graphics board). · · · Indicator status: Green Indicator status: Flashing Green Indicator status: Flashing Yellow 2. (Error messages shown below will remain on the screen for 30 seconds. ) · "No signal detected" error message appears. · "Out of range" error message appears. Whenever an error signal message appears, the signal frequency will be displayed in red. The image vibrates on the screen. Points to check with possible solutions Check that the signal cable is correctly connected to the PC or graphics board. [. . . ] It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e. g. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. [. . . ]