User manual EIZO FLEXSCAN T68

[. . . ] English User's Manual ® F67/FX·D7 T68/TX·D7 Color Display Monitor CONTENTS PRECAUTIONS__________________________ 4 INTRODUCTION _________________________ 9 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1 INSTALLATION ______________________ 10 1-1 Controls & Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Once a priority is set, whenever a change of signal is detected at the selected input, the monitor will switch the input to that signal. 2 SCREEN ADJUSTMENT 33 In the case of only one signal being present at either input, the monitor automatically detects and displays that signal. Priority setting D-Sub Performance If signals from both inputs are present, the monitor gives preference to D-Sub for the cases shown below: · When the power of the monitor is turned ON (see note 1). · When the signal input to D-Sub is changed even if active input was BNC. If signals from both inputs are present, the monitor gives preference to BNC for the cases shown below: · When the power of the monitor is turned ON (see note 1). · When the signal input to BNC is changed even if active input was D-Sub. Select the active input by pressing the input signal selection button on the monitor's front panel. BNC Manual 1 The Input Priority function does not automatically reactivate when the monitor has been in the power save mode. 2 The Input selection button on the front panel can be used to select either D-Sub or BNC as the active input at any time. Beep Use this feature to set the beeper ON or OFF. If the beeper is ON, the monitor will generate beep signals as shown below. · ScreenManager parameter adjusted to minimum or maximum limit. · Monitor received unsupported signal frequency. Long beep Four short beeps 34 2 SCREEN ADJUSTMENT Menu Position, Menu Contrast Use these functions to adjust the position and contrast of the ScreenManager menu. The menu contrast can be set from level 0 (minimum setting) to 5 (maximum setting). E Signal Filter This monitor provides two display modes according to the characteristics of each graphics board for displaying the image properly. If the characteristics of the graphics board does not match those of the monitor, the characters and images displayed may have a slight shadow on their right side (refer to figure below). If this phenomenon is noticeable, use the "Signal Filter" function. Select either mode 1 or mode 2, whichever displays the image better. Reset Use this function to return all ScreenManager parameters (size, position, geometry, color, PowerManager etc. ) to their factory default settings. · · · · Screen: Color: PowerManager: Others: Moiré = OFF Standard/9300K VESA/5 sec. Input Priority = D-Sub Beep = ON Signal Filter = Mode 1 English · Language: 2 SCREEN ADJUSTMENT 35 3 TROUBLESHOOTING 3-1 Troubleshooting This page presents problems that can be corrected by the user. If a problem persists even after applying the suggested remedies, contact an EIZO dealer. n Problems caused by incorrectly setting of the termination switch Problems 1) Misconvergence of colors. (only for the BNC connections. ) Points to check with possible solutions · The termination switch on the rear of the monitor should be set to 75 position (default) for connection to a single monitor. If it is set to the position when using a single monitor, some problems like 1) ~ 4) may occur. Check that the switch position is set to 75 position. n No picture Problems 1) Indicator status: OFF 2) Indicator status: GREEN Points to check with possible solutions · Check that the power cord is correctly connected. (The screen-saver software may be active. ) · Check brightness and contrast settings. Minimum settings will cause screen to be blank. 3) Indicator status: YELLOW · Try pressing a key on the keyboard, or clicking the mouse. [. . . ] Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden. Um einen Abholtermin zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen Sie bitte folgende Rufnummber: 02153-73 35 00. Weitere Informationen finden Sie auch unter der Internet-Adresse: www. eizo. de. Hinweis Die Bildroehre dieses Monitors is frei von Cadmium. EN50082-1:1992 EN61000-3-3:1995 For Europe, etc. (220-240 Vac) Only CE Marking Declaration of Conformity Kind of equipment: Type-designation: is in compliance with: Council Directive 73/23/EEC Council Directive 89/336/EEC Monitor F67 (Model No. [. . . ]