User manual EIZO FLEXSCAN T57S

[. . . ] English CONTENTS PRECAUTIONS INTRODUCTION i 5 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1 FEATURES 6 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 IMAGING ADJUSTMENT - Screen menu - 9 Brightness, Contrast, Size, Position . . . . . . . . . . . . . . . . . . . . [. . . ] Note that brightness and contrast can be adjusted using the short cut keys (see Quick Setup Guide page 6) even while the Control pad is locked. After making such an adjustment, push the ENTER key to clear the brightness/contrast adjustment menu from the screen. Also, the BNC/D-Sub Selection button can still be used. Connecting two PCs to the monitor (Example) MD-C53A (optional) Connect one PC to the monitor's D-Sub connector and another to the BNC connector. The BNC connection should be made with an EIZO BNC cable, available as an option. · Be sure that the monitor and the PC are both switched off before connecting them. · Contact EIZO dealers for information about optional cables. 26 6 GETTING THE MOST FROM YOUR MONITOR Selecting the active input E · The front panel's BNC/D-Sub selection button can be used to select BNC or D-Sub as the active input. · The ScreenManager's "Input Priority" setting (in the 'Others' menu) can be used to set up the automatic selection of the input . See page 23 for details. Linking monitors in a chain Three to four monitors can be chained together so that they can be controlled from a single source. Specifically, you attach BNC coaxial "Y" connectors to the BNC inputs on each monitor. Please make sure the termination switch on each monitor is set appropriately, as described in the chaining procedure. · Any EIZO monitor with a termination switch can be added to the chain. · In order to maintain image clarity, the total length of chained cables should not exceed approximately 8 m (about three to four chained monitors). · Termination switches are effective only with BNC connections. · If a video color printer is included in the configuration, it should be placed at the end of the chain. 6 GETTING THE MOST FROM YOUR MONITOR 27 Chaining procedure 1) Attach BNC coaxial "Y" connectors to each of the BNC inputs (H, V, G, R and B) on the first monitor in the chain (call this Monitor A). Then connect the monitor to the PC, using a signal cable equipped with BNC connectors at the monitor side. 2) Attach BNC coaxial "Y" connectors to the next monitor (monitor B). Connect monitors A and B, this time using a signal cable with BNC connectors at both sides. 3) Connect monitor B to monitor C, and continue in the same manner until all the monitors have been connected in the chain. 4) Set the termination switch on the last monitor in the chain to 75 ohms. Set the termination switches on all other monitors to HIGH IMPEDANCE (). · Use a pen or other implement to set the termination switch. Do not push the switch with a screwdriver or other hard object, as this may cause damage to the switch or the monitor. · When returning to a one-monitor configuration, be sure to reset the termination switch on the monitor to 75 ohms. 28 6 GETTING THE MOST FROM YOUR MONITOR Optional i·SoundTM speaker system The optional speaker system i·Sound connects directly to the monitor and can be used to support multimedia applications. For details, consult EIZO dealers. E 6 GETTING THE MOST FROM YOUR MONITOR 29 7 TROUBLESHOOTING Troubleshooting This page presents problems that can be corrected by the user. If a problem persists even after applying the suggested remedies, contact an EIZO dealer. Problems Problems caused by incorrectly setting of the termination switch. 1) Misconvergence of colors. [. . . ] Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco. se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www. tco-info. com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. [. . . ]