User manual EIZO FLEXSCAN M1700

[. . . ] Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates to ground for safety. Copyright© 2005 EIZO NANAO CORPORATION All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION. EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information confidential unless prior arrangements are made pursuant to EIZO NANAO CORPORATION's receipt of said information Although every effort has been made to ensure that this manual provides up-to-date information, please note that EIZO monitor specifications are subject to change without notice. ENERGY STAR is a U. S. [. . . ] Display a white or gray background image and adjust the <Gain>. NOTE The values shown in the percentage are available only as a reference tool. Reset To return the color settings of the selected mode to the default settings Select the <Reset>. 26 4. Power-save Setup The <PowerManager> menu in the ScreenManager enables to set the power-save setup. NOTE Do your part to conserve energy, turn off the monitor when you are finished using it. Disconnecting the monitor from the power supply is recommended to save energy completely. Analog Input This monitor complies with the "VESA DPMS (Video Electronics Standards Association - Display Power Management Signaling)" (p. Select "VESA DPMS" from the <PowerManager> menu. [Operation] PC Operation Power saving STAND-BY SUSPEND OFF Monitor Operation Power saving Power Indicator Blue Yellow [Power Resumption Procedure] Operate the mouse or keyboard to return to a normal screen. Digital Input This monitor complies with the "DVI DMPM" (p. Select "DVI DMPM" from the <PowerManager> menu. [Power Saving System] PC Operation Power saving Monitor Operation Power saving Power Indicator Blue Yellow [Power Resumption Procedure] Operate the mouse or keyboard to return to a normal screen from the Power save mode of the PC. 4. ADJUSTMENT 27 English Power-save for Speaker When the monitor is in the power-saving mode, sound of speaker also erases simultaneously can be performed. ADJUSTMENT English 5. ATTACHING AN ARM STAND The LCD monitor can be used with an arm stand by removing the tilt stand and attaching the arm stand to the LCD monitor. (Ask your local dealer for information. ) NOTE If you will use the arm or stand of other companies, confirm the followings to the arm or stand maker before selecting. ­ Hole spacing on the arm mounting: 100 mm × 100 mm (VESA compliant) ­ Supportable Weight: Total weight of the monitor (without stand) and attaching equipment such as a cable ­ TÜV/GS approved arm or stand Please connect cables after attaching an arm stand. Setup Procedure 1. Remove the tilt stand by loosening the screws (2 pcs of M4 × 10 mm). Attach an arm stand to the LCD monitor securely. Arm-Stand 4 Mounting Screws (enclosed): M4 × 12 mm 5. ATTACHING AN ARM STAND 29 English 6. TROUBLESHOOTING If a problem persists even after applying the suggested remedies, contact an EIZO dealer. No picture problems : See No. 1 ~ No. 2 Imaging problems : See No. 3 ~ No. 11 Other problems : See No. 12 ~ No. 14 Problems 1. No picture Indicator status: Off Check that the power cord is correctly connected. If the problem persists, turn off the monitor power for a few minutes, then turn it back on and try again. Switch the signal Input by pressing the input signal selection button on the front control panel. (Error messages shown below will remain on the screen for 40 seconds. ) Try pressing a key on the keyboard, or clicking the mouse. 27) These messages appear when the signal is not inputted correctly, even if the monitor functions properly. When the image is displayed correctly after a short time, there is no problem with the monitor. (Some PCs do not output the signal soon after powering on. ) Check that the signal cable is properly connected to the PC or graphics board. Switch the signal input by pressing the Input signal selection button on the front control panel. [. . . ] Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the limits of a Class B digital device. - AC Cord - Shielded Signal Cable (D-SUB mini 15 pin - D-SUB mini 15 pin, the enclesed signal cable) - Stereo mini-jack cable Canadian Notice This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada. Hinweis zur Ergonomie : Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB 2000 mit dem Videosignal, 1280 Punkte × 1024 Zeilen, RGB analog, 0, 7 Vp-p und mindestens 75, 0 Hz Bildwiederholfrequenz, non interlaced. [. . . ]