User manual EIZO FLEXSCAN L997

[. . . ] MAKING USE OF USB (Universal Serial Bus) This manual is checked under the browser settings shown below. Microsoft Internet Exproler: Text size: Medium Encoding: Western European 8. GLOSSARY APPENDIX/ANHANG/ANNEXE About TCO'03 (Applicable gray) About TCO'99 (Applicable black) FCC Declaration of Conformity Hinweis zur Ergonomie / Recycle Auskunft / Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor SAFETY SYMBOLS This manual uses the safety symbols below. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. [. . . ] Power-save Setup The <PowerManager> menu in the ScreenManager enables to set the power-save setup. Do your part to conserve energy, turn off the monitor when you are finished using it. Disconnecting the monitor from the power supply is recommended to save energy completely. Even if the monitor is in a power saving mode, USB compliant devices function when they are connected to the monitor's USB (both the upstream and the downstream ports). Therefore, power consumption of the monitor will change according to the connected devices even if the monitor is in a power saving mode. q q Analog Input This monitor complies with the <VESA DPMS> standard and adopts a power saving method. [Procedure] 1. Select "VESA DPMS" from the <PowerManager> menu. [Power Saving System] PC Operation Monitor Operation Power Indicator Blue Yellow STAND-BY Power saving SUSPEND Power saving OFF [Power Resumption Procedure] Operate the mouse or keyboard to return to a normal screen. Digital Input This monitor complies with the "DVI DMPM". [Procedure] 1. Select "DVI DMPM" from the <PowerManager> menu. [Power Saving System] PC Operation Monitor Operation Power Indicator Blue Yellow Power saving Power saving [Power Resumption Procedure] Operate the mouse or keyboard to return to a normal screen. 5. ActiveShot Function When two PCs are connected to the monitor, ActiveShot (Picture in Picture) function allows you to display both screen images on the Main window and Sub window at the same time. About connecting two PCs to a monitor, See Connecting Two PCs to the Monitor. Operation To display/close the Sub window ON: Press Input Signal Selection Button on the control panel for 2 seconds. Selecting "Off" on the <Picture in Picture> menu will also close the sub window. q To switch the image of main and Sub window Slightly pressing the Input signal selection button (Signal 1-2) switches the signal of Main window and Sub window. r Using ActiveRotationII function. r q q Being in "External" mode of FIneContrast mode. When using the ActiveShot function, some animated images may flicker. 5-2. Sub Window Settings Display Mode <Standard> and <Clip> modes are available for displaying the Sub window (refer to following figures) for displaying the Sub window. The mode is set on the <Picture in Picture> menu of ScreenManager. [Example] <Standard> Mode Displaying the screen image in full screen with reducing the image size. <Clip> Mode Displaying a certain part of the screen image without reducing the image size. <Standard> Mode Displaying the screen image in full screen with reducing the image size in the Sub window. Select <Standard> mode on <Picture in Picture> menu of ScreenManager. To select the size ¡ Select <Window Size>. This sets the window size from "Large" (approx. After selecting the size, the actual Sub window size depends on the input signal. q To adjust the position ¡ Select <Window Position>. This adjusts the position of the Sub window. Select <Window Position> and adjust the position by using the up, down, right and left buttons. To set the Contrast ¡ Select <Window Contrast>. This controls the brightness for the each color (red, blue and green) at the same time. Select <Window Contrast> and adjust by using the right and left buttons. The contrast of sub windows also can be adjusted on the FineContrast menu. Pressing right or left control buttons with displaying the Sub window allows you to display the FineContrast menu. q <Clip> Mode Displaying a certain part of the screen image in the Sub window. Select <Clip> mode on the <Picture in Picture> menu of ScreenManager. Setting up the Clipping Area ¡ Select <Clip Area> icon to set up the clipping area. [Procedure] 1. By selecting the <Clip Area> icon, the Sub window will be displayed in full screen and pink frame will appear on it. [. . . ] increased risks of skin cancer (malignant melanoma) as a consequence. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the inclusion of lead since no replacement has yet been developed. * Bio-accumulative is defined as substances which accumulate within living organisms. ** Lead, Cadmium and Mercury are haevy metals which are Bio-accumulative. Hinweis zur Ergonomie : Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB 2000 mit dem Videosignal, 1600 Punkte x 1200 Zeilen, RGB analog, 0, 7 Vp-p und mindestens 75, 0 Hz Bildwiederholfrequenz, non interlaced. [. . . ]