User manual EIZO FLEXSCAN L795

[. . . ] User's Manual Color LCD Monitor English SAFETY SYMBOLS This manual uses the safety symbols below. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2003 EIZO NANAO CORPORATION All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION. EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information confidential unless prior arrangements are made pursuant to EIZO NANAO CORPORATION's receipt of said information. [. . . ] · The values shown in percentages represent the current level within the specific adjustment. (To create a uniform white or black screen, the percentages for each will probably not be the same. ) <Custom> mode: To adjust the color settings according to your preference To set the Brightness of the screen Use the <Brightness> adjustment. The brightness of the entire screen is controlled by changing the brightness of the backlight. Select <Brightness> in the screen menu and select the brightness by using the up and down buttons and then adjust by using the right and left buttons. NOTE · Directly pressing the control buttons also adjusts the contrast and brightness. Press the <Enter> button to save and exit the settings after the adjustment. To set the Contrast of the screen Use the <Brightness> adjustment. This controls the brightness for the each color (red, blue and green) at the same time. Select <Brightness> in the screen menu and select the contrast by using the up and down buttons and then adjust by using the right and left buttons. NOTE · Percentage except 100 % may cause undisplayable color tone. 4. 51) Set the <Temperature>. The <Temperature> can be set from 4, 000 K to 10, 000 K, in 500 K increments (including 9, 300 K). NOTE · The values shown in the Kelvin are available only as a reference tool. · Setting the temperature under 4, 000 K or over 10, 000 K invalidates the color temperature setting. (The color temperature's setting turns "OFF". ) To change the saturation Use the <Saturation> adjustment. The <Saturation> can be selected from -16 ~ 16. NOTE · The <Saturation> adjustment may cause undisplayable color tone. To change the flesh color, etc. Use the <Hue> adjustment. The <Hue> can be selected from ­20 to 20. NOTE · The <Hue> adjustment may cause undisplayable color tone. To change each color (red, green and blue) Use the <Gain> (p. 50) adjustment By adjusting the red, green and blue color tones for each mode, custom colors can be defined. NOTE · The values shown in the percentage are available only as a reference tool. <Gain> setting returns to the default: All the color indicates 100 %. <sRGB> mode: To select <sRGB> mode Select <sRGB>. To set the Brightness of the screen Use the <Brightness> adjustment. See p. Power-save Setup The <PowerManager> menu in the ScreenManager enables to set the power-save setup. NOTE · Do your part to conserve energy, turn off the monitor when you are finished using it. Disconnecting the monitor from the power supply is recommended to save energy completely. Analog Input This monitor complies with the <VESA DPMS> (p. 50), which works with a blank screen (totally black screen) like "Blank Screen" ScreenSaver software. To use the PC's power saving system (VESA DPMS ). [Procedure] (1) Set the PC's power saving settings. [Power saving system] PC Operation Power saving STAND-BY SUSPEND OFF Monitor Operation Power saving Power Indicator Blue Yellow Operate the mouse or keyboard to return to a normal screen. 4. ADJUSTMENT 29 English To set the power save with ScreenSaver (EIZO MPMS) software [Procedure] (1) Set the PC's appropriate ScreenSaver settings or blank the screen (totally black screen). [. . . ] Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the inclusion of lead since no replacement has yet been developed. * Bio-accumulative is defined as substances which accumulate within living organisms. ** Lead, Cadmium and Mercury are haevy metals which are Bio-accumulative. For U. S. A, Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. [. . . ]