User manual EIZO FLEXSCAN L771

[. . . ] Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2000 by EIZO NANAO CORPORATION. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of Eizo Nanao Corporation. Eizo Nanao Corporation is under no obligation to hold any submitted material or information confidential unless prior arrangements are made pursuant to Eizo Nanao Corporation's receipt of said information. [. . . ] Select "Border Intensity" in the others menu and adjust by using the right and left buttons. Border 4. Color Adjustment The "ColorManagement"menu in the ScreenManager enables to change the color of the screen. Before the Color adjustment · Allow the LCD monitor to stabilize for at least 20 minutes before making color adjustments. · After finishing each adjustment in the custom mode, select "Save" icon to resister the adjustment. · The values shown in percentages represent the current level within the specific adjustment only. (To create a uniform white or black screen, the percentages for each will probably not be the same. ) · Perform the "Range Adjustment" before making the color adjustments. The gradation pattern like below is recommended at the "Range Adjustment". 1. To change the color tone of the white. Set the "Temperature"p. 42) The temperature can be set from 4, 000 K to 10, 000 K , in 500 K increments (except 9, 300 K). To resister the adjustment in the custom mode, select the "Save" icon and then push the enter button. · The values shown in the Kelvin are available only as a reference tool. · Setting the temperature under 4, 000 K or over 10, 000 K invalidates the color temperature setting. (The color temperature's setting turns "OFF". ) · Adjusting the "Gain" (p. (The color temperature's setting turns "OFF". ) 26 4. Adjust the "Saturation" The saturation can be selected from -16 ~ 16. To register the adjustment, select the "Save" icon and then push the enter button. ENGLISH · The "Saturation" adjustment may cause undisplayable color tone. 3. To change the flesh color, etc. Adjust the "Hue" The "Hue" can be selected from -20 ~ 20. To register the adjustment, select the "Save" icon and then push the enter button. · The "Hue" adjustment may cause undisplayable color tone. 4. To adjust each color (red, green and blue). Adjust the "Gain"p. 42) By adjusting the red, green and blue color tones for each mode, custom colors can be defined. To register the adjustment, select the "Save" icon and then push the Enter button. · Adjusting the "Gain" invalidates the color temperature setting. ) · The values shown in the percentage are available only as a reference tool. 4. Power-save Setup This monitor complies with the VESA DPMSp. 43) standard and adopts a power saving method, EIZO MPMS p. 42), which works with a blank screen (totally black screen) like "Blank Screen" ScreenSaver software. 1. To use the PC's power saving system (VESA DPMS ). [Procedure] (1)Set the PC's power saving settings. [Power saving system] PC ON Power saving mode STAND-BY SUSPEND OFF Monitor Operation Power saving LED Green Yellow Power consumption 53 W Less than 3 W Operate the mouse or keyboard to return to a normal screen. 2. To set the power save with ScreenSaver (EIZO MPMS) software. [Procedure] (1)Set the PC's appropriate ScreenSaver settings or blank the screen (totally black screen). (2)Select "EIZO MPMS" from the "PowerManager" menu. [. . . ] CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e. g. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. [. . . ]