User manual EIZO FLEXSCAN L661

[. . . ] User's Manual Color LCD Monitor CONTENTS PRECAUTIONS __________________________ 4 INTRODUCTION _________________________ 9 About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Controls & Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1 INSTALLATION _______________________ 11 1-1 Connecting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Adjusting the "Phase" after the "Clock" adjustment will produce a clear screen. (6) Position Adjusment Function Controls the screen position. a) Select the "Position" icon and push the Enter button to enter the "Position menu. b) Adjust the position of the upper left corner of the image using the Control buttons in order to align the screen. · If vertical bars of distortion appear after finishing the "Position" adjustment, return to "Clock" menu and repeat the previously explained adjustment procedure ("Clock" "Phase" "Position"). 2 USING THE SCREENMANAGER 23 (7) "Resolution" Adjustment Function Controls the contrast of the screen. a) Select the "Contrast" icon and push the Enter button to show the "Contrast/Brightness" menu. b) Confirm if the resolution now being displayed is the same as the input resolution. If it is not, adjust the vertical resolution using the up and down button and adjust the horizontal resolution using the right and left buttons. c) After finishing the adjustment, push the Enter button to memorize the settings and return to the "Screen" menu. Smaller than the actual screen images. Adjusted to actual screen size. Larger than the actual screen images. (8) "Contrast" Adjustment Function Controls the contrast of the screen. b) Press the Auto adjustment button on the front panel while displaying the "Contrast/Brightness menu to automatically adjust contrast. c) The screen blanks for a moment and adjusts the contrast to the maximum level of the current input signal. (continued) OK Too High Too Low 24 2 USING THE SCREENMANAGER Function * In the case of the percentage color flickering between yellow and white, please note that this is not an error but actually the most optimum adjustment point. * The brightness of the entire screen is controlled by changing the "Brightness" controls. No contrast adjustment is required except when the graphics board or the resolution is changed from the previous one. d) Adjust the "Brightness" as desired using the up and down button. e) After finishing the adjustment, push the Enter button to memorize the settings and return to the "Screen" menu. E (9) Exit the ScreenManager a) To return to the main menu, select the "Return" icon or push the down button twice, followed by the Enter button. b) To exit the ScreenManager, select the "Exit" icon and push the Enter button. Double clicking the Enter button at any time also exits the ScreenManager menu. · In the "Enlarged" mode and the "Full" mode (refer to the page 30), the following adjustment is available. Function Smoothing Displays blurred texts distinct. ·This adjustment is disable when the resolution is 1280 x 1024 or 1280 x 960. 2 USING THE SCREENMANAGER 25 2-3 Color Adjustment About Color Adjustments Entering the ScreenManager, select the "Color" icon and push the enter button to show the "Color" menu. The ScreenManager "Color" menu provides 3 color setting modes; 1, 2, and 3. You can also adjust the color settings for each mode and store them for future use. · Allow the monitor to warm-up for at least 20 minutes before making an adjustment. Color Mode Function Color Mode (Standard) Adjusts: Color Mode Mode 1(default): The normal white color. The white color tone is slightly reddish. · The contrast level is reduced in Mode 2 and 3. (a) Select the "Color Mode" icon from the "Color" menu and push the Enter button. [. . . ] It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e. g. increased risks of skin cancer (malignant melanoma) as a consequence. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. [. . . ]