User manual EIZO FLEXSCAN L560T-C

[. . . ] (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 Trade name: EIZO Model: FlexScan L560T-C declare that the product is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] It can be downloaded from the EIZO homepage (http://www. eizo. com/). 3. Adjust by using <Screen> menu in the ScreenManager. (1) Vertical bars appear on the screen Use the <Clock> (p. 35) adjustment. Select the <Clock> and eliminate the vertical bars by using the Right and Left of the Control Buttons. Do not continuously press the Control Buttons, as the adjustment value will change quickly and make it difficult to locate the most suitable adjustment point. If the horizontal flickering, blur or bars appear, proceed to <Phase> adjustment as follows. (2) Horizontal bars appear on the screen. Select the <Phase> and eliminate the horizontal flickering, blurring or bars by using the Right and Left Buttons. NOTE · Horizontal bars may not completely disappear from the screen depending on the PC. 4. The correct displayed position of the monitor is decided because the number and the position of the pixels are fixed. The "Position" adjustment moves the image to the correct position. Select <Position> and adjust the position by using the Up, Down, Right and Left Buttons. If vertical bars of distortion appear after finishing the <Position> adjustment, return to <Clock> adjustment and repeat the previously explained adjustment procedure. Clock Phase Position 4. To adjust the output signal range (Dynamic Range) of the signal. Use the <Range Adjustment> (p. 36). This controls the level of output signal range to display the whole color gradation (256 colors). [Procedure] Press the Auto Adjustment Button on the control panel while displaying the <Range Adjustment> menu to automatically adjust the range. The screen blanks for a moment, and adjusts the color range to display the whole color gradation of the current output signal. 5. To smooth the blurred texts of the enlarged screen of the lower resolutions. Switch the <Smoothing> setting. <Smoothing> is clear-cut the letters or lines. Select <Smoothing> in the screen menu and select the suitable level from 1 ~ 5. NOTE · The "Smoothing" is disabled in the resolution 1280 x 1024. · Since the displayed image is enlarged, the blurred texts may not be necessarily lost completely. 22 4. Color Adjustment In the analog input, perform the "Range Adjustment" (p. 22) before making the color adjustments. The <Color> menu in the ScreenManager enables to change the color of the screen. By using the <Color Mode>, the adjustment mode can be selected from <Custom mode> (to adjust the color settings according to your preference) and <sRGB> mode. NOTE · Allow the LCD monitor to stabilize for at least 20 minutes before making image adjustments. (Allow the monitor to warm up for at least 20 minutes before making adjustments. ) · Performing the <Reset> of the <Color> menu returns the color settings to the default settings. [. . . ] The customer or the user of the FlexScan L560T-C can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the FlexScan L560T-C as recommended below, according to the maximum output power of the communications equipment. Rated maximum output Separation distance according to frequency of transmitter power of transmitter m 150kHz to 80MHz 80MHz to 800MHz 800MHz to 2. 5GHz W d = 1. 2 P d = 1. 2 P d = 2. 3 P 0. 01 0. 12 0. 12 0. 23 0. 1 0. 38 0. 38 0. 73 1 1. 2 1. 2 2. 3 10 3. 8 3. 8 7. 3 100 12 12 23 For transmitters rated at a maximum output power not listed above, the recommended separation distance "d" in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where "P" is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. [. . . ]