User manual EIZO FLEXSCAN L351

[. . . ] Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2000 by EIZO NANAO CORPORATION. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of Eizo Nanao Corporation. Eizo Nanao Corporation is under no obligation to hold any submitted material or information confidential unless prior arrangements are made pursuant to Eizo Nanao Corporation's receipt of said information. [. . . ] · To unlock Switch off the monitor's power, then hold down the brightness selection button once again and turn the power back on. 3. ScreenManager 15 Off Timer The off timer function causes the monitor to automatically enter a power off state after a predetermined amount of time has lapsed. This function was created to reduce afterimage p. 27) characteristics that are particular to LCD monitors when the monitor screen is left on for a long period without use. [Procedure] (1) Select "Off Timer" in the ScreenManager "Others" menu. (2) Select "Enable" and press the right and left buttons to adjust the "On Period" (1 to 23 hours). in "On period" "On period" expired *1 Monitor Operation Advance Notice *1 "Power Off" Mode LED Green Green Flashing Flashing yellow slowly Advance notice (LED flashing green) will be given 15 minutes before the monitor automatically enters the "Power Off" mode. To delay entering the "Power Off" mode, press any button during the advance notice period. The monitor will continue to operate for an additional 90 minutes. Press any button to return to a normal screen. · The off timer function works while the PowerManager is active, but there is no advance notice before the monitor's power is switched off. 16 3. Screen Adjustment The monitor displays the digital input image correctly based on its pre-setting data. However, if the image position is not incorrect or larger than the actual image screen, please adjust the following adjustment items using the "Screen" menu of the ScreenManager. ENGLISH · Allow the monitor to warm up for at least 20 minutes before making any adjustments. 1. The screen position is incorrect. "Position" adjustment The correct displayed position of the monitor is decided because the number and the position of the pixels are fixed. The "Position" adjustment moves the image to the correct position. Select "Position" and adjust the position of the upper left corner of the image by using the up, down, right and left buttons in order to align the screen. 2. Screen image is smaller or larger than the actual screen images. "Resolution" adjustment Adjustment is needed when the input signal resolution and the resolution now being displayed are different. Select "Resolution" and confirm if the resolution now being displayed is the same as the input resolution. If it is not, adjust the vertical resolution using the up and down button and adjust the horizontal resolution using the right and left buttons. Smaller than the actual screen images. Adjusted to actual screen. Larger than the actual screen images. 4. Adjust the " Smoothing" Select a suitable level from 1~5 (soft ~ sharp). Select "Smoothing" and adjust by using the right and left buttons. 4. Set the Brightness of the screen Adjust the "Brightness" This controls the brightness of the screen. The brightness of the entire screen is controlled by changing the brightness of the backlight. [Brightness 1 & Brightness 2] The L351 has two memories for the preferable brightness setting (Brightness 1 & Brightness 2). The brightness selection button on the front panel can be used to select Brightness 1 or Brightness 2. [Power saving system] PC On Power saving Off mode Monitor Operation Power saving Power saving LED Green Yellow Flashing yellow (2 times for each) Power consumption 35 W Less than 3 W Less than 1 W ENGLISH Operate the mouse or keyboard to return to a normal screen from the Power save mode of the PC. [. . . ] It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e. g. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. [. . . ]