User manual EIZO FLEXSCAN L350

[. . . ] English User's Manual FlexScan L350 Color LCD Monitor â CONTENTS PRECAUTIONS __________________________ 4 INTRODUCTION _________________________ 9 About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Controls & Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1 INSTALLATION _______________________ 11 1-1 Connecting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · To make adjustment easily, install and run the "Screen Adjustment Program" in the attached utility disk. · Do not continuously press the Control buttons (up, down, right and left buttons) on the front panel, as the adjustment value will change quickly and make it difficult to locate the most suitable adjustment point. E Procedure Please adjust the screen using the following procedure. (1) Having read the "readme. txt" file, install and run the "Screen Adjustment Program" in the utility disk. Follow the wizard or the procedures (2) to (7) below. · If the user's operation system has no utility disk (e. g. OS/2), we recommend setting the desktop pattern to that as shown in the diagram below. Every-other-dot pattern (2) Auto Adjustment Push the Auto adjustment button on the front panel. The following message will appear and remain on the screen for 5 seconds. While the message is on the screen, push the button again to automatically adjust the screen position. If you do not wish to do adjust the screen, do not push the button again. The message will disappear. · The Auto adjustment function is intended for use on Macintosh and PCs running Windows. It may not function properly if any of the following applies: 2 USING THE SCREENMANAGER 19 · PC running MS-DOS (not Windows). · The background color for the "wallpaper" or "desktop" pattern is set to black or dark. · Some signals from some graphics boards may not function properly. clock icon) appear on the screen continuously. (Example) (3) Enter the ScreenManager "Screen" menu. (4) "Clock" Adjustment Function Decreases the vertical bars of distortion. a) Select the "Clock" icon and push the Enter button to enter the "Clock" menu. b) If horizontal bars appear, these can be eliminated by adjusting the right and left buttons. c) Press the Enter button to memorize the setting and return to the "Screen" menu. i) If the screen is free from any bars of distortion, proceed to "Position" adjustment. ii) If horizontal flickering or horizontal bars appear, proceed to "Phase" adjustment. · The LCD monitor is designed for analog input signals from a standard graphics board. The analog input signal is converted to a digital signal by the LCD circuitry. To convert the signal correctly, the LCD monitor needs to produce the same number of clock pulses as the dot clock of the graphics system. When the clock pulse is not correctly set, some vertical bars of distortion are displayed on the screen. · When adjusting the "Clock", the horizontal screen size will also change. 20 2 USING THE SCREENMANAGER (5) "Phase" Adjustment Function Eliminates the horizontal bars of distortion. [. . . ] It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e. g. increased risks of skin cancer (malignant melanoma) as a consequence. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. [. . . ]