User manual EIZO FLEXSCAN F930

[. . . ] English User's Manual FlexScan F930 Color Display Monitor ® CONTENTS PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Controls & Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To decrease the vertical bars on the right side of the charactor or image. To return ScreenManager parameters to their factory default setting. E 1. Power-save Setup (To link with PC'S Power saving system) The PowerManager function sets the monitor's power-save environment to match the PC's ScreenSaver software. The PowerManager feature automatically reduces the monitor's power consumption during idle periods. The acronym VESA stands for "Video Electronics Standards Association, " and DPMS stands for "Display Power Management Signaling. " DPMS is a communication standard that PCs and graphics boards use to implement power savings at the monitor side. · For the PC setup, refer to the user's manuals for the PC amd graphics board. · Do your part to conserve energy, turn off the monitor when your finished using it. Complete energy use can only be stopped by disconnecting the monitor from the power supply. · When the monitor is in a power saving mode, the optional EIZO i·Sound speaker unit will turn off. · Off Timer will work while PowerManager is active, but there will be no advance notice before the monitor's power switches off. 2 SCREEN ADJUSTMENT 19 Procedure 1) First, make the appropriate settings for the PC. 2) Select "On" in the "PowerManager" menu. Power saving method of VESA DPMS and the monitor VESA DPMS utilizes four signals: ON, STAND-BY, SUSPEND, and OFF. The monitor detects these signals from the graphics board and executes power-saving accordingly, as shown in the table below. Signal ON STAND-BY SUSPEND OFF Screen Operation Blank Blank (Mode 1) Blank (Mode 2) LED Green Green Flashing green Yellow Power consumption 130 W (normal) 80% of normal less than 10 W less than 3 W 2. Power-save Setup (To set the period in which the monitor will be in operation) The Off Timer function allows the user to set the time in which the monitor will be in operation, called the "On Period" and automatically shifts the operation into the "Off Timer Mode" when the set "On Period" expires. The energy consumption of the monitor in the "Off Timer Mode" is as low as the one of the monitor in "PowerManger Mode 2" although no setting PC to operate the Off Timer function is required. 2) Press the right/left key to adjust how long (0 to 23 hours) the monitor should be in the "On Period". Advance notice (LED flashing green) will be given 15 minutes before the monitor automatically enters the "Off Timer Mode". · To delay entering the "Off Timer Mode", press any keys on the front panel located to the left of the power switch during the "Advance notice Mode". Delayed entrance into the "Off Timer Mode" can be extended as many times as desired. 20 2 SCREEN ADJUSTMENT 3. To decrease a slight shadowed image or charactor on its right side This monitor provides signal filter adjustments according to the characteristics of each graphics board for displaying the image properly. If the characteristics of the graphics board does not match those of the monitor, the characters and images displayed may have a slight shadow on their right side (refer to figure below). Procedure 1) Select from mode 1 or mode 2, whichever displays the image better in the Signal Filter 1 menu. E 4. To decrease the vertical bars on the right side of the charactor or image This monitor provides signal filter adjustments according to the characteristics of each graphics board for displaying the image properly. If the characteristics of the graphics board does not match those of the monitor, the characters and images displayed may have a couple of bars on their right side. [. . . ] The relevant TCO'99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e. g. [. . . ]