User manual EIZO FLEXSCAN F520

[. . . ] English User's Manual FlexScan F520 Color Display Monitor CONTENTS PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Controls & Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1-1 Connecting the monitor to the PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The monitor detects these signals from the graphics board and executes power-saving accordingly, as shown in the table below. Signal ON STAND-BY SUSPEND OFF Screen Operation Blank Blank (Mode 1) Blank (Mode 2) LED Green Green Flashing green Yellow Power consumption 80 W (normal) 80% of normal less than 10 W less than 3 W Off Timer What is Off Timer?The Off Timer function allows the user to set the time in which the monitor will be in operation, called the "On Period" and automatically shifts the operation into the "Off Timer Mode" when the set "On Period" expires. The energy consumption of the monitor in the "Off Timer Mode" is as low as the one of the monitor in "PowerManger Mode 2" although no setting PC to operate the Off Timer function is required. Set-up Procedure 1) Select the "Off Timer" icon. 3) Press the right/left key to adjust how long (1 to 23 hours) the monitor should be in the "On Period". Advance notice (LED flashing green) will be given 15 minutes before the monitor automatically enters the "Off Timer Mode". 2 SCREEN ADJUSTMENT 13 To Delay Entering the "Off Timer Mode" To delay entering the "Off Timer Mode", press any keys on the front panel located to the left of the power switch during the "Advance notice Mode". Delayed entrance into the "Off Timer Mode" can be extended as many times as desired. "ENERGY STAR" is a set of power saving guidelines issued by the U. S. The guidelines apply to PC systems and peripherals. 2-3. Shortcut Keys Before entering the ScreenManager, brightness and contrast can be adjusted directly by moving the Control pad. To record the new setting and exit the ScreenManager, press the Enter key. (The brightness and contrast functions are also available in the ScreenManager "contrast/brightness" menu. ) Brightness Up Contrast Down Brightness Down Contrast Up 2-4. Adjustment Lock The ScreenManager operation can be disabled by holding down the up arrow key on the control pad while switching on the monitor's power. This will disable ("lock") the ScreenManager, protecting from accidental changes. To unlock the buttons: switch the power off, then hold down the up arrow key on the control pad once again and turn the power back on. Note that brightness and contrast can be adjusted using the shortcut keys even while the Control pad is locked. After making such an adjustment, push the ENTER key to clear the brightness/contrast adjustment menu from the screen. Up Arrow Key of the Control Pad Power Switch 14 2 SCREEN ADJUSTMENT 3 TROUBLESHOOTING Troubleshooting If a problem persists even after applying the suggested remedies, contact an EIZO dealer. E Problems 1) Indicator status: OFF 2) Indicator status: GREEN 3) Indicator status: GREEN (flashing) 4) Indicator status: YELLOW 5) Indicator status: YELLOW (flashing) Points to check with possible solutions Check that the power cord is correctly connected. (The monitor may be in a power saving mode. ) Try pressing a key on the keyboard, or clicking the mouse. (The monitor may be in a power saving mode. ) Try pressing any keys on the front panel, or switch the monitor off and then on. (The monitor may be in "Off Timer Mode". ) If the problem persists, switch off the monitor power for a few minutes, then switch it back on and try again. 6) Following message appears. Check that the PC is switched ON. Check that the signal cable is properly connected to the graphics board or PC. Check that the graphics board is correctly inserted in the PC. 7) Following message appears. (Example) Use the graphics board' utility software to change the s frequency setting. (Refer to the manual of the graphics board. ) · Whenever an error signal message appears, the signal frequency will be displayed in red. [. . . ] The relevant TCO'99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e. g. [. . . ]