User manual EIZO DURAVISION FDV1002

[. . . ] Important Please read this User's Manual carefully to familiarize yourself with safe and effective usage. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: DuraVision FDX1002/FDV1002 is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ] · Used to select the setting or adjustment items, or to increase or decrease the adjustment values on each menu. · When the settings menu is not displayed, pressing or switches between displaying and not displaying the crosshair. Indicates monitor's operation status. 3 button 4 button 5 Power indicator 6 7 8 9 10 11 12 13 button USB port (Down) Power jack (DC-IN) Input signal connector Input signal connector Input signal connector Cable holder Cable tie Blue : Operating Orange : Power off Captures a screenshot of the currently displayed image. D-Sub mini 15-pin connector × 1 S-Video input connector × 1 Video input connector × 1 Covers the monitor cables. Clinches the cables. 10 Chapter 1 Introduction Chapter 2 1 Connecting Cables 2-1. Connection Procedures Connects to external equipment compatible with the monitor. When used as a PC monitor page 11 When using video equipment page 12 When used as a PC monitor ATTENTION · When replacing the current monitor with an FDX1002 / FDV1002 monitor, be sure to change the PC settings for resolution and vertical frequency to those which are available for the FDX1002 / FDV1002 monitor referring to the resolution table (see below) before connecting the PC. Compatible Resolutions/Frequencies The monitor supports the following resolutions. FDX1002 Resolution 640 × 400 640 × 400 640 × 480 640 × 480 720 × 400 800 × 600 832 × 624 1024 × 768*1 *1 Display Mode NEC PC-9801 NEC PC-9821 Apple Macintosh VGA, VESA VGA TEXT VESA Apple Macintosh VESA Frequency 56 Hz 70 Hz 67 Hz ~75 Hz 70 Hz ~75 Hz 75 Hz 60 Hz Dot Clock ~65 MHz Recommended resolution (Set this resolution. ) FDV1002 Resolution 640 × 480 640 × 480 Display Mode Apple Macintosh VGA Frequency 67 Hz 60 Hz Dot Clock ~31 MHz Chapter 2 Connecting Cables 11 (1) Connect the monitor to the PC with a signal cable that matches the connectors. After connecting the cable connectors, tighten the screws of the connectors to secure the coupling. PC monitor D-Sub mini 15-pin connector Signal cable MD-C87 (optional) D-Sub mini 15-pin connector or DVI connector Signal cable FD-C16 (optional) When using video equipment (1) Connect the monitor to the video equipment with a signal cable that matches the connectors. monitor Video equipment S-Video S-Video cable (Commercially available product) S-Video or Video Video cable (Commercially available product) Video 1 Chapter 2 Connecting Cables 2 Plug the power cord of the monitor into a power outlet. (1) Connect the power cord to the AC adapter. (2) Connect the AC adapter to the Power jack of the monitor, and after that, connect the power plug to a power outlet. ATTENTION · This product does not include a power cord. Please provide separately a power cord which meets the usage requirements. · For the maximum power saving, it is recommended that the Power button be turned off. Unplugging the power cord completely shuts off power supply to the monitor. 2-2. Adjusting the Screen Angle Hold left and right edge of the monitor with both hands, and adjust the tilt and swivel to the best condition for working. Chapter 2 Connecting Cables 1 Chapter 3 Settings and Adjustments 3-1. Basic Operation and Functions Basic operation of Setting menu 1 2 Displaying Setting Menu Press . Setting/Adjusting 3 Exiting Choose [Exit] with NOTE or , and press . · Keeping pressed for 2 seconds will also exit the Setting menu. 1 Chapter 3 Settings and Adjustments Functions The settings adjustable in the Setting menu are as shown below. The availability of items depends on the input signal. : Configurable : Not configurable Tab Color Setting / adjustable item Brightness Contrast Black Level Sharpness Saturation Hue PC Settings Clock Phase Position Range Adjustment Color Mode Red/Green/Blue Reset Reset Others Video Aspect Power Save Reverse Crosshair Color Width Beep Language Date/Time File Information PC Video page 17 Reference page 16 Chapter 3 Settings and Adjustments 1 3-2. Please switch between the input screens you want to adjust and adjust them one by one. Adjustable item / adjustable value Brightness Contrast Black Level Sharpness Saturation Hue PC Settings *1 Adjusting Adjusts the brightness of the backlight. Provides automatic adjustment when you want every color gradients displayed. 1/2/3 0 - 128 Select Color Mode (1/2/3) to adjust the colors of red, green and blue in several modes. Resets the state adjusted with the [Color] tab to the factory default (excluding [PC Settings]). 0 - 30 0 - 30 0 - 30 Off/Low/High -30 - +30 -30 - +30 Clock Phase Position Range Adjustment Color Mode*2 Red/Green/ Blue Reset Reset *1 This setting becomes available when a PC is connected to the monitor. Please adjust with a PC when display and color adjustments are required. Perform [Range Adjustment] before adjusting Color Mode. *2 1 Chapter 3 Settings and Adjustments 3-3. Configure other settings This will configure other settings. Setting item / setting value Video Aspect Normal/100% Setting Configures the display range of the input image (overscan). "Normal" : Displays the input image with the outmost parts slightly cut off. [. . . ] It is recommended that range adjustment be made before color adjustment. Resolution The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This monitor consists of 1024 (FDX1002) / 640 (FDV1002) horizontal pixels and 768 (FDX1002) / 480 (FDV1002) vertical pixels. At a resolution of 1024 × 768 (FDX1002) / 640 × 480 (FDV1002), all pixels are illuminated as a full screen (1:1). Chapter 5 Reference 5-4. Preset Timing The following table shows the factory preset video timing of the PC. ATTENTION · Display position may be deviated depending on the PC connected, which may require screen adjustment using Setting menu. [. . . ]