User manual EIZO COLOREDGE CG210

[. . . ] ADJUSTMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4-1. CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 9. GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 11. APPENDIX/ANHANG/ANNEXE . . . . . . . . . . . . . . . . . . . . . . . . 46 About TCO'03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 FCC Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Hinweis zur Ergonomie / Recycle Auskunft / Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 SAFETY SYMBOLS SAFETY SYMBOLS This manual uses the safety symbols below. [. . . ] Do not continuously touch the Directing switches, as the adjustment value will change quickly and make it difficult to locate the most suitable adjustment point. If the horizontal flickering, blur or bars appear, proceed to <Phase> adjustment as follows. (2)Horizontal flickering, blurring or bars appear on the screen. Select the <Phase> and eliminate the horizontal flickering, blurring or bars by using the Right and Leftswitches. NOTE · Horizontal bars may not completely disappear from the screen depending on the PC. The correct displayed position of the monitor is decided because the number and the position of thepixels are fixed. The <Position> adjustment moves the image to the correct position. Select <Position> and adjust the position by using the Up, Down, Right and Left switches. If vertical bars of distortion appear after finishing the <Position> adjustment, return to <Clock> adjustment and repeat the previously explained adjustment procedure. ("Clock" "Phase" "Position") 24 4. ADJUSTMENT (4)Screen image is smaller or larger than the actual screen images. Adjustment is needed when the input signal resolution and the resolution now being displayed are different. Select <Resolution> and confirm if the resolution now being displayed is the same as the input resolution. ADJUSTMENT Adjustment Contents Menu Brightness Function Descriptions To set the brightness of the screen 0~100% Adjustable range Tips · The values shown in the "%" are available only as a reference tool. · Directly touching the Up and Down switches also adjusts the brightness. Touch the Enter switch to save and exit the settings after the adjustment. To set the color temperature 4000K~10000K in 500 K increments (including 9300 K) Temperature Tips · Setting the value to "Off" presents the natural color temperature of the panel. · The values shown in the Kelvin are available only as a reference tool. · Setting the temperature under 4000 K or over 10000 K invalidates the color temperature setting. (The color temperature's setting turns "OFF". ) Gamma · Setting the <Gain> invalidates the <Temperature> adjustment. To set the gamma value 1. 8~2. 6 Tips · If setting the gamma value, the using the monitor in the digital signal input is recommended. If using the monitor in the analog input signal, set the gamma value from 1. 8 to 2. 2. To change the saturation -100~100 Setting the minimum level (-100) turns the image to the monochrome. Saturation NOTE Hue · The <Saturation> adjustment may cause undisplayable color tone. -100~100 NOTE Gain · Using <Hue> adjustment may not obtain proper tone reproduction. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. [. . . ]