User manual EINHELL RT XM 305

[. . . ] Read and follow the operating instructions and safety information before using the equipment for the first time. Safety Information Layout Items supplied Intended use Technical data Before starting the equipment Operation as wood/plastics saw Operation as metal saw Transport Replacing the power cable Cleaning, maintenance and ordering of spare parts Disposal and recycling Page 21 21 21 22 22 23 24 26 26 26 26 26 When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety information with due care. Keep this manual in a safe place so that the information is available at all times. [. . . ] place the 45° stop angle (b) between the blade (7) and the turntable (17). Adjust the adjustment screw (37) so that the angle between the blade (7) and the turntable (17) equals exactly 45°. 100 mm it is possible to fix the saw's drag function with the locking screw for drag guide (25) in rear position. If the cutting width exceeds 100 mm you must ensure that the locking screw for drag guide (25) is slackened and that the machine head (4) can be moved. Use the handle (1) to push back the machine head (4) and fix it in this position if required (dependent on the cutting width). Place the piece of wood to be cut at the stop rail (11) and on the turntable (17). Lock the material with the clamping device (8) on the fixed saw table (18) to prevent the material from moving during the cutting operation. With the drag guide (24) fixed in place: Use the handle (1) to move the machine head (4) steadily and with light pressure downwards until the saw blade (7) has completely cut through the workpiece. With the drag guide (24) not fixed in place: Pull the machine head (4) all the way to the front and then use the handle (1) to move it downwards steadily and with light pressure. Now push the machine head (4) slowly and steadily to the very back until the saw blade (7) has completely cut through the workpiece. When the cutting operation is completed, move the machine head (4) back to its upper (home) position and release the ON/OFF button (2). Do not simply let go of the handle (1) after cutting, but allow the machine head (4) to rise slowly, applying slight counterpressure as it does so. 1-3, 31) The crosscut saw can be used to make crosscuts of 0°- 52° to the left and 0° - 60° to the right in relation to the stop rail. Press the latched position lever (13), turn the turntable (17) and scale pointer (15) to the desired angular setting on the dial (16) and lock into place with the locking grip (14). 1-3, 32) The crosscut saw can be used to make miter cuts of 0° - 45° in relation to the work face. If necessary, dismantle the clamping device (8) or mount it on the opposite side of the fixed saw table (18). Undo the locking screw (22) and use the handle (1) to tilt the machine head (4) to the left until the pointer (20) coincides with the required value on the scale (19). Retighten the locking screw (22) and make the cut as described in section 7. Carefully clean the flange screw (39), outer flange (40) and inner flange. The cutting angle of the teeth, in other words the direction of rotation of the saw blade (7) must coincide with the direction of the arrow on the housing. Check to make sure that all safety devices are properly mounted and in good working condition before you begin working with the saw again. Every time that you change the saw blade, check to see that it spins freely in the table insert (12) in both perpendicular and 45° angle settings. [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade or industrial applications. [. . . ]