User manual EINHELL RGH 2040

[. . . ] Collecting the shredded material The shredded material bag supplied with the machine can be placed under the chute opening. Follow the operating instructions step-by-step and use the pictures provided as a visual guide to easily assemble the machine. Mains voltage: Power input: Idle speed n0: Branch diameter: LpA sound pressure level: LWA sound power level: Weight: 230 V ~ 50 Hz 2000 W 4500 rpm max. 1 2 3 4 5 6 7 12 Loading funnel inlet Loading funnel Motor housing with cutter plate Prodder Complete chassis Wheels Axle (complete with washers and nuts) The machine can be switched ON (switch position "I") and OFF (switch position "0") using the ON/OFF switch (Figure 1/Item 11). [. . . ] Judge the quantity of material which you put into the loading funnel so that it does not clog. If you want to shred withered, damp material that has been lying in the garden for several days, alternate between putting in this material and branches. This will help to prevent the loading funnel becoming clogged with material. Entangled branches and leaves should be thoroughly shredded before loading any more material. Do not allow the ejector outlet of the funnel to become clogged with shredded material ­ since this may result in material pile-ups. If you have to replace any blade, you must only use genuine blades to ensure that they meet the relevant quality and safety criteria. Please note: For safety reasons we recommend that you have all sharpening and blade replacement work carried out by a specialist workshop. Before carrying our any inspection or servicing work on the machine, disconnect it from the power supply by disconnecting the machine connection cable (extension) from the machine plug. This will help to keep the machine in good working order and is the basis for a long working life. When you have finished your work, pull the loading funnel forwards and clean the inside. When you close the loading funnel, make sure that the safety switch and the release screw are clean. Clean the plastic body and other plastic parts with a mild household cleaning agent and a damp cloth. Please provide the following information on all orders for spare parts: Model/type of tool Article number of the tool ID number of the tool Number of the required spare part For our latest prices and information please go to www. The shredder and its accessories are made of various types of material, such as metal and plastic. The machine does not work a) No power at the plug b) Machine is switched off c) Overload switch has tripped d) Ejector chute is blocked e) Loading funnel is not secure on the motor housing a) Blades worn a) Check the power cable and fuse b) Switch on machine c) Press control on overload switch b) Clean ejector chute e) Clean interior and tighten safety screw a) Turn, sharpen or replace blades The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of ISC GmbH. T For EU countries only Never place any electric tools in your household refuse. To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its implementation in national laws, old electric tools have to be separated from other waste and disposed of in an environment-friendly fashion, e. This can also be done by handing over the used device to a returns center, which will dispose of it in accordance with national commercial and industrial waste management legislation. This does not apply to the accessories and auxiliary equipment without any electrical components which are included with the used device. T Given unfavorable conditions in the power supply the equipment may cause the voltage to drop temporarily. If the supply impedance "Z" at the connection point to the public power supply exceeds 0, 391 Ohm it may be necessary to take further measures before the equipment can be used as intended from this power supply. If necessary, you can ask your local electricity supply company for the impedance value. [. . . ] The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. In order to assert your guarantee claim, please send your defective device postage-free to the address shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of purchase. [. . . ]