User manual EINHELL BGT 63

[. . . ] If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions. Carrying strap Combined oil/petrol cylinder Spark plug wrench Open-ended spanner (8 mm / 10 mm) Allen key (size 4) Allen key (size 6) 2 x cable ties The operating instructions as supplied by the manufacturer must be kept and referred to in order to ensure that the machine is properly used and maintained. Any use which is not expressly permitted in the manual may result in damage to the machine and place the user in serious danger. [. . . ] 3 Fuel mixture table Mixing procedure: 25 parts petrol to 1 part oil Petrol 1 liters 2 liters 40 ml 200 ml 2-stroke oil 7. 2 Starting the engine when warm (if the machine has not been switched off for more than 15 ­ 20 minutes) 1. Secure the throttle lever (in the same way as described in "Starting the engine when cold"). Hold the machine firmly and pull out the starter cable until you feel it start to resist. If the machine does not start after 6 pulls, repeat steps 1 ­ 7 of the procedure for starting the engine from cold. 3 Switching off the engine Emergency Stop procedure: If it becomes necessary to stop the machine immediately, set the ON/OFF switch to "Stop" or "0" Normal procedure: Let go of the throttle lever and wait until the engine has changed to idling speed. 4 Practical tips Practice all operating techniques with the engine switched off before you start to use the machine. EXTENDING THE CUTTING LINE WARNING: Do not use any kind of metal wire or metal wire encased in plastic in the cutting head. To extend the cutting line run the motor at full speed and tap ("BUMP") the cutting head on the ground. The blade on the safety shield will cut the line to the appropriate length (Fig. DIFFERENT CUTTING METHODS If the machine is correctly assembled with the safety hood and cutting head it will cut weeds and long grass in places with difficult access, for example along fences, walls and foundations and also around trees. PREVENTING RECOIL When you work with the blade there is a risk of recoil if it strikes solid objects such as tree trunks, branches, tree stumps, stones or the like. This will throw the equipment backwards in the direction opposite to the rotation of the tool. Do not use the metal blade near fences, metal posts, boundary stones or foundations. Always switch off the machine and pull out the spark boot plug before carrying out any maintenance work. Place the new cutting line in the center and attach the resulting loop to the recess in the spool splitter (Fig. The spool splitter will separate the two halves of the nylon line (Fig. Hook the last 15 cm of the two ends of the line to the line holders opposite the line spool (Fig. Thread the two ends of the line through the metal eyelets in the line spool housing (Fig. L2/Item 1) in the line spool housing lock into the appropriate recesses (Fig. Pull the two line ends briefly and powerfully to release them from the line holders in the line spool. This will reduce the load on the engine when Fit the line spool again. [. . . ] The engine does not run smoothly Mauvaise distance entre les Nettoyez la bougie dallumage et électrodes de la bougie dallumage réglez la distance entre les électrodes ou montez une nouvelle bougie dallumage. K t p erklärt folgende Konformität gemäß EU-Richtlinie und Normen für Artikel declares conformity with the EU Directive and standards marked below for the article déclare la conformité suivante selon la directive CE et les normes concernant larticle verklaart de volgende conformiteit in overeenstemming met de EU-richtlijn en normen voor het artikel declara la siguiente conformidad a tenor de la directiva y normas de la UE para el artículo declara a seguinte conformidade de acordo com a directiva CE e normas para o artigo förklarar följande överensstämmelse enl. K t p erklärt folgende Konformität gemäß EU-Richtlinie und Normen für Artikel declares conformity with the EU Directive and standards marked below for the article déclare la conformité suivante selon la directive CE et les normes concernant larticle verklaart de volgende conformiteit in overeenstemming met de EU-richtlijn en normen voor het artikel declara la siguiente conformidad a tenor de la directiva y normas de la UE para el artículo declara a seguinte conformidade de acordo com a directiva CE e normas para o artigo förklarar följande överensstämmelse enl. The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of ISC GmbH. [. . . ]