User manual EIKI LC-SM1

[. . . ] MULTIMEDIA PROJECTOR MODEL LC-SM1 OWNER'S MANUAL LC-SM1 TO THE OWNER Before operating this projector, read this manual thoroughly and operate the projector properly. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. [. . . ] Press POINT LEFT button to lighten the color and press POINT RIGHT button to deepen the color. (From 0 to 63. ) Contrast Press POINT LEFT button to decrease contrast, and press POINT RIGHT button to increase contrast. (From 0 to 63. ) Brightness Press POINT LEFT button to adjust the image darker, and press POINT RIGHT button to adjust brighter. (From 0 to 63. ) Gamma Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. Quit Closes the PICTURE IMAGE ADJUSTMENT Menu. NOTE: The Fine sync and the Total dots cannot be fully adjusted when "RGB, " "HDTV1O35i" or "HDTV1O8Oi" is selected on the SYSTEM MENU (P22 and 23). NORMAL FUNCTION The normal picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Unit). The "Normal" display will be displayed on the screen for a few seconds. 26 COMPUTER MODE AUTO IMAGE FUNCTION The Auto Image function is provided to automatically adjust Fine sync, Total dots, and Picture Position for most computers. 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select AUTO IMAGE and press the SELECT button. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN button. Change the setting On or Off by pressing the SELECT button. 2 Fine sync Adjust the picture as necessary to eliminate flicker from the display. (Refer to page 26. ) Total dots The number of the total dots in one horizontal period. (Refer to page 27. ) 3 Move the arrow to "Go!" and press the SELECT button to start the Auto Image function. This adjustment can be executed by pressing AUTO IMAGE button on the Remote Control Unit. Closes the AUTO IMAGE FUNCTION Menu. Stored Go Quit NOTE: The Fine sync and the Total dots cannot be fully adjusted when "RGB, " "HDTV1O35i" or "HDTV1O8Oi" is selected on the SYSTEM MENU (P22 and 23). The Fine sync, Total dots, and Picture Position of some computers may not be fully adjusted with the Auto Image Function. (Refer to page 26 to adjust "Fine sync" or "Total dots" and page 27 to adjust Picture Position. ) PICTURE POSITION ADJUSTMENT The position of the image can be adjusted vertically and horizontally through PICTURE POSITION ADJUSTMENT. 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select POSITION and press the SELECT button. Move the image by pressing the POINT UP / DOWN / RIGHT / LEFT buttons. To cancel PICTURE POSITION ADJUSTMENT, press any button except POINT buttons. To return to the position previously set, press NORMAL button. 2 27 This projector has a picture screen resize function, which enables you to display the desirable image size. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SCREEN and press the SELECT button. Move the arrow to the function that you want to select and then press SELECT button. True To make the image into its original size select True in the dialog box. When the original image size is larger than the screen size (800 x 600), this projector enters Digital Zoom mode automatically. [. . . ] NOTE :Moving the projector from a cool temperature location to a warm temperature location may result in moisture condensation on the lens. In such an event, leave the projector OFF and wait until condensation disappears. (See "SETTING" section on page 32. ) Check Display feature. (See "SETTING" section on page 32. ) · · · Check the connection between the computer or video equipment and the projector. When turning the projector on, it takes about 30 seconds to display the image. [. . . ]