User manual EFD ULTRA TT BLUETOOTH CONFIGURATION PROCEDURE

[. . . ] Insert the Socket Installation CD into the computer's CD-ROM drive Use My Computer or Internet Explorer to access the CD-ROM drive. Click on the "Cordless Serial Adapter" icon that was placed on your desktop to open the program. Click the Properties button on the main window. 2. 4. 5. 3 ® A NORDSON COMPANY Ultra TT Bluetooth® Configuration Procedure 6. Select the COM port to which the Socket adapter is connected and click "OK. " Click here to change PORT Click "OK" once correct PORT is selected 7. On the General tab, enter EFxxxxx (where xxxxx is the 5-digit serial number of the Ultra TT unit) in the Friendly Name box. NOTE Once you have configured a Socket adapter for a specific Ultra TT, it is recommended that you do not use that adapter on a different Ultra TT unit to avoid confusion during Pairing (ref: Section III). [. . . ] Verify that EFD Ultra TT PDA Software Version 1. 2 is installed on the PDA by tapping the top-left corner on the Main screen and choosing "About. " If not, install according to the instructions on the CD included with the Ultra TT Bluetooth Kit. Verify that the configured Socket Adapter is connected to the Ultra TT. From the front panel, select Setup -> Next -> Configure Serial Ports -> Data Bits 8 to configure the Ultra TT's front and rear COM ports for Bluetooth. NOTE To use a Teach Pendant Cable (PN # 700818) with a non-Bluetooth PDA or teach pendant, you must select "Data Bits 7. " 6. Highlight the name or serial number entered when you configured the Socket Adapter in Section I, then tap "Connect. " 10. Verify that the "Add to trusted devices list" option is NOT selected, then tap "OK". 9 ® A NORDSON COMPANY Ultra TT Bluetooth® Configuration Procedure Important Notes Recharge the PDA and sync it to your computer at the end of every day. Otherwise, you might lose the information entered since the last sync session. The next time you want to connect to the Ultra TT using the same PDA, launch the EFD Ultra TT PDA Application. When asked if you wish to reconnect to the last device you communicated with, select "Yes" and go through the re-initialization steps. If you are using a new PDA or a different PDA from the one last used/paired with the Ultra TT, you must perform steps 7-10, Section 3 again to pair the new PDA with the Socket Adapter installed on the Ultra TT. If the PDA ever gets out of range of the Ultra TT (approximately 30 feet), Communications Error #1104 will occur. The Bluetooth connection will be re-established automatically when the PDA comes back within range. If the PDA powers down, it may be able to reconnect without restarting the Ultra TT and the EFD Ultra TT PDA Application by waiting 8-10 seconds. In this case, the Bluetooth Reconnect window will pop up and communication will be established. (If the Reconnect window does not pop up, restart the application by returning to PDA Home and relaunching the EFD Ultra TT PDA Application. ) 10 ® A NORDSON COMPANY Ultra TT Bluetooth® Configuration Procedure Appendix A EFD Ultra TT PDA Application Firmware Upgrade Overview This procedure describes how to upgrade the EFD Ultra TT PDA Application firmware on the Ultra TT using a PDA. Note that the PDA software must first be loaded onto a computer so that the firmware data file can be hot-synced (copied) to the PDA. You will also need the restoration diskette or mini CD that came with your Ultra TT to restore system parameters or "personalities" after the firmware update. If you are unable to locate your restoration disk or did not receive one with your Ultra TT system, please contact your local Ultra TT sales representative. NOTE After flashing the firmware, all dispensing programs will be erased from the TT! Be sure that all dispensing programs have been hot-synced and backed up on your computer prior to performing the firmware upgrade. After the upgrade, you will need to download your dispensing programs to the TT again using the PDA. Copy the firmware file (. MOT) from the Ultra TT CD to the EFD sync folder (C:\Programs Files\Palm\<your PDA name>\EFD\Sync) on your computer. (If you do not have this folder on your computer, you must first install the EFD PDA software from the CD that came with your Ultra TT. ) 2. Copy the SNxxxxx. ACL recovery file from the Ultra TT mini-CD or diskette to the EFD sync folder. Hot-sync your PDA to copy the files from the computer to the PDA. 11 ® A NORDSON COMPANY Ultra TT Bluetooth® Configuration Procedure B. [. . . ] This is for the front panel connector used by the PDA, not the back panel 9-pin connector. Set the baud rate on the PDA to 9600 by using the "Baud Rate:" drop-down list at the top of the "Controller Options" window. Once the firmware re-flash is successful, remember to change SW2-1 back to the OFF position and set the PDA's baud rate back to 115200. The socket adapter is configured to "Notify Local Host of Bluetooth Events". [. . . ]