User manual EFD ULTRA 325 TT QUICK START GUIDE

[. . . ] Insert the holding pins into the holes on the back plate to fit the size barrel you are using. Insert the luer end of the barrel into the barrel stop and twist the barrel onto the captive luer extender. Attach the barrel adapter to barrel and plug the male quick connect into the P1 connector (0~100 psi) for dispensing high-viscosity fluid or P2 (0~30 psi) for dispensing low-viscosity fluid. [. . . ] Download the Software Installation CD that was included with the PDA to the PC. Copy the EFD PDA software to the palmOne Quick Install and then HotSync to install the EFD PDA software to the palm. Connect the Socket Bluetooth® adapter to the RS232 connector at the back of the Ultra TT. Reset the EMO switch on the front panel and press the green power button to power up the machine. (Do not check "Add to trusted device list". ) Wait for the message "Connection established to selected device". Return to the Main screen, select Setup and the message "Dispenser is about to Home" will display. Tap OK to home the machine. Air 2 Pulsed air line White (female) quick-connect P1 Use 6mm OD tubing to connect the air to the main air input on the back of the machine. It is recommended that either the 2000F755TT (5 micron filter regulator) or 2000F756TT (includes coalescing filter) be incorporated between the factory air supply and the Ultra TT System. 2000F755TT or 2000F756TT Air input hose Step 3: Single Air Input Valve Attach the valve to the appropriate valve bracket. Fluid reservoir air is connected to P2 or to auxiliary air connector on top of the Z-head. The fluid reservoir tank should be placed to the side of the machine or if using cartridges, attached to the T-slots on the Z-plate. To pressurized reservoir or cartridge Step 3: Auger Valve Attach the 790 auger valve to the auger valve bracket (#700806). Barrel reservoir air is connected to the P2 connector on top of the Z-head. The brown (+) lead is connected into Terminal 1 and the white (-) lead is connected to terminal 2 of the (4) position connector on top of the Z-head. Fluid feed hose 5 0 20 I/O Dispense Head Terminal 1 HS Terminal 2 I/O Dispense Head P1 P2 AUX AIR HS P1 P2 AUX AIR Black (male) quick-connect P2 752V-UHSS Valve P2 Tooling Plate 5 7 Install the EFD universal fixture plate (#7007-300 or #7007-500) or your own tooling plate. Note: Dimensional drawings for the Y-carriage can be found on the CD-ROM included with this machine. Caution: Failure to level your work-holding fixture may result in difficulties when programming. TTSERIES ® A NORDSON COMPANY Programming Follow the tutorial in the manual on the operations CD-ROM. This will teach you how to program all the essential elements of a fluid-dispensing program. If you have any questions regarding your new Ultra TT Automation Series system, please contact EFD or their authorized representative. 3 Helpful Hints ­ Pressure, Speed, Time and Tip Size control deposit size. [. . . ] Changing pressure to compensate for reduced flow is the least reliable method to compensate for flow reduction. ­ Locate a point or mark on your part that you can use to orient the tip to when creating a new tip offset. ­ Remove the shipping bolt on top right-hand corner of Z-plate. For application assistance in the USA, call 800-556-3484. For EFD sales and service in over 30 countries, contact EFD USA or go to www. efd-inc. com/contact ® A NORDSON COMPANY EFD Inc. , a Nordson Company 977 Waterman Avenue East Providence, RI 02914-1342 USA telephone +1 401-434-1680 fax +1 401-431-0237 automation@efd-inc. com www. efd-inc. com/xyz Palm is a trademark of Palm, Inc. [. . . ]