User manual EFD PM6500

[. . . ] Task- and equipment-specific warnings, cautions and instructions are included in equipment documentation where appropriate. Qualified Personnel Equipment owners are responsible for making sure that EFD equipment is installed, operated and serviced by qualified personnel. Qualified personnel are those employees or contractors who are trained to safely perform their assigned tasks. They are familiar with all relevant safety rules and regulations, and are physically capable of performing their assigned tasks. Intended Use Use of EFD equipment in ways other than those described in the documentation supplied with the equipment may result in injury to persons or damage to property. Some examples of unintended use of equipment include, but are not limited to: · · · Using incompatible materials Making unauthorized modifications Removing or bypassing safety guards or interlocks · · · Using incompatible or damaged parts Using unapproved auxiliary equipment Operating equipment in excess of maximum ratings Regulations and Approvals Make sure all equipment is rated and approved for the environment in which it is used. [. . . ] Or if you prefer, follow the instructions in the enclosed "Welcome" letter to contact your EFD representative. Connect Power · Connect the power plug to the power pack. The unit is shipped with a USA-compatible plug and three international plugs. Connect the power cord into your local power source. · · Connect Air Input NOTE: Clean, dry, filtered factory air is required to meet the warranty. If your air supply is not filtered, order the EFD five micron filter regulator (EFD part# 2000F755). · · · · Push one end of the air input hose into the input fitting on the back of the ProcessMate. DO NOT exceed 110 psi (7. 5 bar) or damage to the unit may occur. Getting Started Connect Thermocouple 4 5 6 · · Plug K-type thermocouple lead into the back panel of ProcessMate. Connect the other end of the lead to process hardware. *Option: Can route thermocouple lead with either air line tubing inside insulation. See directions below. NOTE: Longer Thermocouple leads may be used when required. Using a different type will result in incorrect temperatures. Attach Process Feed Lines · · Slide insulation over cold process feed line. *Option: Can route thermocouple lead with either hot or cold process feed line. · · Insert cold process feed line into the cold process fitting. Insert hot process feed line into the hot process fitting. Connect Exhaust Mufflers · Insert a muffler into each exhaust port for both cold and hot feed exhausts. NOTE: Tubing can be purchased as an accessory to route for remote exhaust in lieu of mufflers. 9 Features & Controls: Front & Rear Panels Digital display Power switch Air switch Flow control knob Air input Power cord Thermocouple to Exhaust feed line to Exhaust feed line Cold process feed line Hot process feed line CMW No. 1 display STOP OUT Temperature unit Alarm output indicator Level key No. 2 display Mode key Up/Down keys 10 Front Panel Digital Display Digital Display Level key Mode key No. (Refer to manufacturer's documentation supplied with unit. ) Use to access advanced features of the controller (Refer to manufacturer's documentation supplied with unit. ) Actual temperature as measured by the thermocouple. Process temperature set point. Up/down keys Use the keys to change the temperature set point value displayed on the No. Al CMW STOP OUT Alarm indicator light--this will light up whenever the unit is adding cold air to the process. Communications writing enable/disable indicator lights Control stop indicator Control output 1 & 2 indicators Advanced features NOT used by ProcessMate Change from Centigrade to Fahrenheit · · · · Hold down the Level Key for 3 seconds. Return to the Temperature Display by holding the Level Key for 3 seconds Air Settings OFF (Center) MAX Air Stops all air from flowing through the unit. Once near to the desired temperature, the "ADJ AIR" setting should be used. The plastic can be cut to customize the box to fit individual process requirements. If the box becomes soiled or damaged, replacements are readily available from EFD. Can I Make My Own Process Chamber?For those who wish to make their own process chamber, please follow the guidelines outlined below: · · · · The chamber should cover the entire material path (syringe, valve, fittings, etc, leaving only the needle or exit point exposed). The less space inside the chamber, the easier it is to maintain temperatures within. [. . . ] 15 EFD One Year Limited Warranty All components of the ProcessMate Temperature Control Unit are warranted for one year from date of purchase to be free from defects in material and workmanship (but not against damage caused by misuse, abrasion, corrosion, negligence, accident or faulty installation) when the equipment is installed and operated in accordance with factory recommendations and instructions. Within the period of this warranty, EFD will repair or replace free of charge any part of the equipment thus found to be defective, on authorized return of the part prepaid to our factory during the warranty period. In no event shall any liability or obligation of EFD arising from this warranty exceed the purchase price of the equipment. Before using, user shall determine the suitability of the product for his intended use, and user assumes all risk and liability whatsoever in connection therewith. [. . . ]