User manual DYNASTY SPAS EXCALIBUR

[. . . ] Owner's Information Owner's Information Dealer Company Address Phone E-Mail Installer Company Address Phone Warranty Turned In / Date Model Serial Number Equipment Pack Color Date of Delivery We Appreciate your business and our sincere desire is that you receive years of pleasure and therapy from your Dynasty Spa. Please call your local Dynasty Spa Dealer if you have any questions or problems. If they are unavailable, please feel free to call the Dynasty Spas Customer Service Group at: 800-951-6224. TM Dynasty Spas Owner's Manual Dynasty Spas Owner's Manual Table Of Contents Owner's Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . Pre-Operation Instructions. . . . . . . . . . . . . . . . . . . 11 SSPA System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 MSPA System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The "Set Point" symbol indicates the desired temperature, NOT the current water temperature!Water temperature can be adjusted by 1° An irregularly flashing "Filter Cycle" icon means that the system has stopped filtering after 3 hours because water temperature exceeds Set Point by more than 2°F (1°C). If temperature cools down to 1°F (0. 5°C) above Set Point before the scheduled end of the cycle, filtering will resume for the remainder of the programmed duration. Troubleshooting Pumps have started up for one minute on several occasions and "Filter Cycle" icon is flashing. Our Smart Winter Mode protects your system from the cold by automatically turning the pumps on for one minute several times a day to prevent water from freezing in pipes. Water temperature is displayed. The system will reset automatically when water reaches 109°F (43°C). Call your dealer or service supplier if problem persists. 3 flashing dots are displayed. Call your dealer or service supplier if problem persists. The display is flashing. Press any key to reset the system, then reprogram all desired parameters. 15 5000 Top Side Control Instructions 7 Temperature unit Step Programming Sequence Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Time of day Filter cycle start time Filter cycle duration Filter cycle frequency Economy mode start time Economy mode duration Storing settings in memory & returning to Normal mode Filter Cycle Heater icon icon Up & Down arrows Programming Mode Economy ModeLock icon icon icon Step 1- Time of day Setting the time: 1- Enter Programming mode by holding Prog. 3- Use Up and Down arrows to change 10:25 am 11:43 pm Step 4- Filter cycle frequency Setting filter cycle frequency: FF06 FF10 "xx" day. 1- Press Prog. 2- The display will show FFxx, with representing the frequency per Steps 2 & 3- Filter cycle start time & duration Steps 5 & 6- Economy mode start time & The system automatically performs two filter cycles per day, at 12-hour intervals. During the filter Setting Economy mode start time: cycle, Pumps 1 & 2 and the blower will run for one minute, then Pump 3 will run for one minute. Pump 1 will then run at low speed for a programmed 2- The display will show ESxx, with "xx" ES10 number of hours. The "Filter Cycle" icon lights up representing the starting hour. To program a filter cycle, you must enter: 1) the time you want the cycle to start and 2) the duration of the cycle. If no filtering is required, the duration Setting Economy mode duration: should be set to "0". 2- The display will show Edxx, with "xx" Ed04 representing the duration in hours. Setting filter cycle start time: 3- Use Up and Down arrows to change Ed06 setting. FS10 2- The display will show FSxx, with "xx" representing the starting hour. FS08 3- Use Up and Down arrows to change Step 7- Storing settings in setting. key a seventh time to store the settings in Setting filter cycle duration: the system's non-volatile memory and to return to Normal mode. Fd04 2- The display will show Fdxx, with "xx" representing the duration in hours. Fd06 3- Use Up and Down arrows to change setting. 16 5000 Top Side Control Instructions Digital control pad This function allows you to prevent unauthorized parameter setting of the unit. [. . . ] Air lock Adjust bleed screw located on spa wall next to skimmer area. Jets won't come on Probable Cause #1 Action Probable Cause #2 Action Pump not primed. Check to see that pump is purged in. 29 Trouble Shooting Guide (cont. ) Low water flow Probable Cause #1 Action Probable Cause #2 Action Probable Cause #3 Action Dirty Filter Remove filter cartridge and clean. Low voltage or incorrect voltage Have a Licensed Electrician check the line voltage Spa is leaking Probable Cause #1 Action Loose connection. Check joints and unions Motor does not run Probable Cause #1 Action Probable Cause #2 Action Probable Cause #3 Action No power to motor. [. . . ]