User manual DYMO RHINOPRO 5000

[. . . ] See Figure 2. Getting Started Follow the instructions in this section to print your first label. Power Supply The printer is powered by standard batteries, a rechargeable battery pack or an AC power adapter. To save power, the printer will automatically turn off after five minutes of inactivity. Inserting the Batteries The printer uses six AA batteries. Press the thumb latch on the bottom of the printer to open the battery compartment door. See Figure 1. Figure 2 2 3 Manual_RhinoPRO5000_WEU. indd 3 3 23-07-2004 10:51:10 3. [. . . ] Text size and other settings remain unchanged. 6 mm (1/4") 1 9 mm (3/8") 2 12 mm (1/2") 2 19 mm (3/4") 4 Escape Key The Escape key returns you to the starting point from within any function. To create a multi-line label 1. Repeat these steps for each additional line. Adding Symbols The printer supports the extended symbol set as shown in Figure 8. , \ ( ~ ) ² ; ° _ @ ± ' & " ? Navigation Key You review and edit your label using the arrows on the Navigation key. You can also view menu choices, and then press to make a selection. Designing Your Label You can choose from a number of formatting options to enhance the appearance of your labels. Figure 8 To add a symbol 1. When you locate the symbol, press to add the symbol to your label. Changing the Font Size You can print the text on your label in five font sizes: extra-small, small, medium, large, and extralarge. XS S M L XL The font size you can use depends on the size of label tape that is installed in the printer. 6 6 23-07-2004 10:51:26 Manual_RhinoPRO5000_WEU. indd 6 In addition, commonly used electrical and datacom symbols are available on individual keys for easy entry. Deleting a Label from Memory When you no longer need a stored label, you can delete it from memory. Use the arrow keys to move to the memory location that contains the label you want. Press +0 and then press to clear the memory location. Using International Characters The printer supports the extended Latin character set using RACE technology. Similar to using a mobile phone keypad, typing a letter multiple times quickly will scroll through variations of that letter. For example, if French is selected as the language and you repeatedly press the letter a, you will see a à â æ and so on through all the variations available. The character variations and the order in which the variations appear depend on the language you have selected to use. Using the Quick Access Keys Your printer includes several quick access keys that give you direct access to printing specific types of labels. Quick access keys are available for printing wrap-around, fixed-length, patch panel, module, vertical, and barcode labels. Saving your Label You can save up to eight labels in memory. Memory locations that contain a stored label are filled and when the cursor is positioned over a location, the contents are displayed. Press to save the label. Printing Wrap-Around Labels You can create labels that wrap around a cable or wire. The text is placed vertically or horizontally along the width of the cable and repeated so that you can read the label from any angle. The text is automatically repeated over the width of the label. 123 123 123 123 123 123 Recalling from Memory Once a label is saved to memory, you can recall the label to print or edit. Use the arrow keys to find the memory location for the label you want and then press . 123 123 123 123 123 123 123 123 123 7 Manual_RhinoPRO5000_WEU. indd 7 7 23-07-2004 10:51:29 Printing Fixed Length Labels Normally, the length of the label is determined by the length of the text entered. However, you may wish to make a label for a specific purpose that is a fixed length regardless of the length of the text. You can specify a fixed length for a label in 0. 5 mm (0. 2") increments between 10 mm (0. 4") and 999. 9 mm (40. 0"). Any change you make to the fixed length setting remains in effect until you change it. If multiple copies of a fixed-length label are printed, cut marks are printed between each label. See Figure 9. Cut Marks To print a patch panel label using serialization 1. The default is 12 mm (0. 5") and the value can be set in increments of 0. 1 mm (0. 005"). [. . . ] Check for label jam, empty label cassette, discharged batteries, or other problems. · Insert a larger size label cassette, or · Decrease the size of the label content. Insert a new label cassette Replace batteries or connect AC power adapter. · Clean cutter blade. If you still need assistance, contact DYMO Customer Support for your country. [. . . ]