User manual DURKOPP 804-1

[. . . ] The instruction manual contains important information on how to operate the machine securely, properly and economically. Observation of the instructions eliminates danger, reduces costs for repair and down-times, and increases the reliability and life of the machine. The instruction manual is intended to complement existing national accident prevention and environment protection regulations. The instruction manual must always be available at the machine/sewing unit. [. . . ] 9805 7804-113 7. 2 Operating the touch screen panel Activate a function by touching (with a fingertip) the symbol representing the function in question on the screen. ­ Tip with your fingertip on the requested function symbol. 7. 2. 1 Window "General" ­ 7. 2. 2 Input window Close the window "Cancel" "ESC" - > the window will be closed, the value will not be modified "OK" "CR" -> the window will be closed and the new value will be saved, if it is within the specified limit values 18 7. 2. 3 Selection window On this screen, the following actions can be executed: ­ If the button is bright it cannot be activated. ­ A field, in this case the sewing program, has been selected and can be edited or appended. 1 7. 2. 4 Numeric input for a parameter The title bar indicates the parameter group. ­ The "DEL" key cancels an input. 19 7. 2. 5 Numeric input for a parameter ­ ­ Enter the password. It will be switched over to the technician level. 7. 2. 6 Input of a text "ESC" "Aa" "DEL" "CR" Close the window Switching from capitals to small letters Deleting the last characters Close the window, the sequence name will be adopted. 20 7. 2. 7 Radio- button With the Radio-button the selected option is marked with a black dot. 1 7. 2. 8 "Scroll bar" 2 Move the scroll bar 2 downwards. The lower part of the screen will be displayed. 21 7. 2. 9 Check- button With the Check-button the selected option is marked with a black x. 7. 3 The start screen The start screen appears after switching the sewing unit on. ­ Press the "Service" button in order to switch to the multitest program. Press the "Language" button in order to change the selected language. ­ 22 7. 4 The main screen 2 1 3 15 4 5 6 7 8 9 10 11 1 14 1 2 3 4 5 6 7 8 9 10 11 12 13 Title bar Sequence name: Number of sewing programs in the sequence Time: Hour: Minute Repair mode Seam pattern size Max. thread tension Stitch length Number of stitches / Bobbin thread consumption Button bobbin change Button counter reset Slider, Tabs, Buttons for sequence control. Popup-Menu Active sewing program Seam pattern 12 13 14 15 23 7. 5. Pop up menu structure · File ¡ ¡ ¡ ¡ Delete Copy Open New · · · Edit Seam program Sequence ¡ Save as ¡ Machine parameters ¡ Sequence ¡ Seam program · · · · Extras Parameters Contour adjustment Testing contour ¡ Full screen on/off ¡ Zoom on/off ¡ Service · · · · · · Adjustments System information Multi-test Initialization and update Manufacturer Correction ¡ Thread tension ¡ Sewing speed 24 7. 6 Menu item "File" It is possible to sew a single sewing program several times consequently or to sew several different sewing programs one after the other in a sequence. After actuating the pedal one more time the right side will be closed. After actuating the pedal the right part of the two-piece clamp for an angular feed will be closed. Mode 4 Quick start mode The clamp will be opened in the feeding position. With the change-over clamp, the seam will be started automatically after feeding. This mode is only active if the quick start has been enabled with the machine parameters. In order to activate the quick start mode, the machine must be switched off and on again! 30 Mode 5 The clamp remains closed in the feeding position. Feeding position (on/off) With the feeding position activated the clamp goes to the requested position in order to facilitate the feeding of the material. = -90 mm) PP3 - Deposit mode: Deposit mode The following modes can be set: Mode 1 (def. ) The clamp will be opened in the deposit position. After actuating the pedal the left part of the two-piece clamp for an angular feed will be opened. After actuating the pedal one more time the right side will be opened. After actuating the pedal the right part of the two-piece clamp for an angular feed will be opened. [. . . ] Pedal actuation Depending on the preselected direction of the movement the clamp goes step by step to the right/left or downwards/upwards. 52 7. 11. 1 Creating a new seam contour Step 1 In the first step the starting point of the seam segment is determined. 1 ­ ­ Go to the desired starting point by using the arrow keys "ñ " , "ò " , "ñ " or "ò ". Pay attention to the specific clamp limits so that the seam contour is inside the possible sewing field and that no collision will take place!The input of circular arcs requires particular attention since the intermediate points will be interpolated! 53 Step 2 In the second step it will be determined whether: · · ­ ­ a non sewing line a line or a circular arc will be sewn. Select the "Line sewing" or "circular arc" button. [. . . ]