User manual DURACRAFT DA5020

[. . . ] Do not use any product with a damaged cord or plug of if product malfunctions, is dropped or damaged in any manner. Do not run power cord under carpets & do not cover with throw rugs. Do not operate the Air Cleaner near a humidifier or in a bathroom or laundry area. [. . . ] Use Filter-Change Calendars to keep track of filter replacement cycle for both filters. NOTE: Filters are not washable. STEP 3: · Make sure that speed control is set to the OFF position. Plug in Air Cleaner. CLEAN ING NOTE: Prior to any cleaning operation, the Air Cleaner must be turned off and unplugged from the wall outlet. Clean all external surfaces especially the air intake grills and the air outlet area. STEP 4: OPERA TION STEP 1: · Inspect Air Cleaner upon removal from its container. Remove and discard any packaging material. · Set speed control and IONIZER control (for Models DA-5020 & DA-5030 only) to desired settings. Step 4 IONIZER STEP 2: · Place the air cleaner on a flat, level, unobstructed surface. SUP ER OFF HIG H SILE NT 2 POWER STEP 5: · Replace Pre-filter once every 3 months. Replace HEPA filter once every 2 E L E C T R I C A L R AT I N G S This product is rated at 120 Volts A. C. , 60 Hz with a power consumption of 135 Watts. The ionization voltage is 7500 Volts D. C. CARTRIDGE REPLACEMENT FILTER CARTRIDGE REPLACEMENT NOTE: Neither the prefilter nor the HEPA filter are washable. Step 2: To open, gently from the internal chamber. Step 5: Locate the seam Step 7 of the pre-filter and carefully separate the fastener on the seam from the prefilter and remove the prefilter from the HEPA filter. Step 5 place the air cleaner on its side and unscrew the locking handle under its base to release the BASE from the air cleaner. Step 2 IF REPLACING ONLY THE PRE-FILTER, SKIP TO STEP 7. Step 7: Remove any packaging or plastic from the new pre-filter and remove any additional fasteners from the box. Secure approximately 1/2 inch of the strap fastener to one edge of the carbon pre-filter (on the white side). Carefully wrap the pre-filter around the HEPA filter so that the ends meet and the white side is facing outwards. Close the product by replacing the base and tightening the locking handle. Step 9: Turn the air cleaner upright, plug into wall socket and turn on. Unit HEPA Filter with Pre-Filter Base Locking Handle Step 3: Remove the BASE assembly. Step 4: Remove the filter assembly (consisting of the HEPA and pre-filter) CARTRIDGE REPLACEMENT cont. FILTER REPLACEMENT REMINDER Filter Change Schedule: ­ Pre-Filter: 3 Months ­ HEPA Filter: 2 Years · Upon start up of your air cleaner and upon every Pre-filter replacement, roll the Pre-Filter 3 Month Filter- Change Calendar ahead 3 months to indicate when the next filter replacement is necessary (Fig. 1). MAY 8-14 the right) to indicate when filter replacement is necessary (fig. 1 · Upon start up of your air cleaner and upon every HEPA filter replacement, roll the HEPA Filter-Change Calendar ahead 2 years (use the month wheel on the left and the year wheel on DA-5010 HEPA Filter DA-5020 HEPA Filter DA-5030 HEPA Filter LIMITED WARRANTY DA-5010, DA-5020, DA-5030 D U R A C R A F T ® H E PA AIR CLEANING SYSTEM MODEL SERIES DA-5010/ DA-5020/DA-5030 This product has been engineered and crafted with great care for your satisfaction. Be sure to fill out and return the enclosed card within 7 days of purchase. This 3 year limited warranty applies to repair or replacement of product found to be defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. [. . . ] Return defective product to the following address with a brief description of the problem. Include proof-of-purchase and a $10. 00 check or money order for handling, return packing and shipping charges. Mark carton "Attention Repair Department. " Ship to: Repairs Department 4755 Southpoint Drive Southpoint Distribution Center Memphis, TN 38118 U. S. A. [. . . ]