User manual DUNE HD SMART B1

[. . . ] Playlists: build playlists from your folders, use your own playlists, use repeat and shuffle functions. nAS function: access files on storage devices (HDD , optical drive , etc) attached to the player from the local network (using SMB or FTP). BitTorrent: use built-in BitTorrent client to download files from P2P networks. Customizable user interface: work with media collections using cover art and icon browsing (with Full HD graphics). [. . . ] Make sure to switch off the player and all relevant A/V equipment before connecting them. Ensure your TV and other A/V equipment are configured to use proper inputs. The player will perform its initial loading procedure, which may take up to about 1 minute. during the loading procedure , "DUNE" logo is shown on the TV. If you do not see "DUNE" logo on the TV when you switch on the player, it may mean some problem with the connection between the player and the TV or that a wrong video input is chosen in the TV or A/V receiver/switch. In such a case, recheck the cables and the settings of the TV or A/V receiver/switch, or try to use different cables or a different way of connecting the player to the TV. If you see "DUNE" logo on the TV when you switch on the player, but then the picture disappears and no other picture appears during at least 10 seconds, it may mean that a wrong video output mode is configured in the player. In such a case, press the "MODE" RC button, and then press one of the RC buttons "1", "2", "3", "4" or "5" to switch to a different video output mode (see "Quick Setting of Video Output Mode"). The main screen shows items allowing to use different player functions and access all storage devices and network drives connected to the player. Adjust the player settings as needed using "SETUP" item on the main screen of the player menu (or by pressing the "SETUP" RC button). in particular , you may want to adjust video settings , audio settings , and network settings. To connect the player with an installed internal HDD via USB slave, switch off the player, connect the USB slave port of the player to the USB host port of the PC, and then switch on the player. After finishing working with the player in the PC, ensure the USB device is correctly stopped in the PC («Safely remove hardware» or a similar function), switch off the player, and then disconnect the USB slave port of the player from the USB host port of the PC. To connect a network drive using SMB or NFS protocol, ensure you are on the main screen of the player menu, press the "MENU" RC button, and choose "Create Network Folder", then fill the parameters of the network drive as needed. the player will show an item corresponding to the configured network drive on the main screen. To browse the list of network resources accessible via SMB or UPnP protocols, use "Network Browser" item on the main screen of the player menu. NOTE: If some network resources are not shown by the player, you may need to wait some minutes and then retry (or press the "MENU" RC button and choose "Refresh" command). To format a HDD attached to the player, select the drive item on the main screen of the player menu, press the "INFO" RC button and choose "Format Disk" (to format the entire disk) or "Format Partition" (or to format an already existing disk partition only). NOTE: To use disks formatted by the player on a Windows PC, you may need to install additional software on the PC, such as "EXT2FSD" (http://www. To switch on the player, ensure the power switch on the rear panel is in "on" state, and press the "POWER" RC button or the "on/off" button on the front panel. To put the player into the standby mode, press the "POWER" RC button or the "on/off" button on the front panel. Depending on the player settings (see the player setup menu), the "hardware standby" or "software standby" mode may be used. [. . . ] The Dune HD Smart player itself is a head unit which can be extended at user's desire with extension modules, such as the following: Dune HD Smart HE (adds the option for easy installation of SATA 3. Extension modules can work exclusively with the head unit (Dune HD Smart player) and use a common control system, implemented via the head unit. The number of connected modules may vary in a wide range: the user can compile his/her own Dune HD Smart system of e. In order to group SMART devices by 2 or 3 horizontally, special mounts can be used. [. . . ]