User manual DUAL XIA5600

[. . . ] · Do not install the amplifier where it may be exposed to moisture. Remember to test all amplifier functions before completing the final mounting procedure. TYPICALMOUNTINGMETHOD 2 XIA5600INSTALLATION NOTE:Besuretofollowspecificinstructionsincludedwithyouramplifierinstallation kit(notincludedwiththisamplifier). Theinformationbelowshouldbeusedageneral guidelineonly. PowerWire(+12V) · Disconnect negative battery terminal before proceeding. Begin by routing the power +12V wire from the battery to the amplifier location. [. . . ] 3 XIA5600INSTALLATION ConnectionsandControls 1 2 3 4 5 6 7 14 13 12 11 10 9 8 1 2 3 4 5 6 7 Low Level Inputs High Level Inputs Input Level Control Crossover Frequency Crossover Mode Switch Bass Boost LED Indicator 8 9 10 11 12 13 14 Ground Connection Remote Connection +12VDC Battery Connection Main Fuses illuminite Fuse illuminite Outputs Speaker Connections 4 XIA5600INSTALLATION TypicalWireRouting MainPowerConnections Connect +12V, GND and REM wires accordingly. A suitable fuse MUST be installed on the +12V lead within 18" of the battery for protection of the vehicle's electrical system. FuseRating When replacing fuses, make sure new fuse is the correct type and amperage. Mainfuse 30 amp ATO x 3 illuminitefuse 2 amp ATO x 1 Power/GroundWireSize For optimum performance, use only the wire size listed below or larger. Power/ground4 gauge illuminiteoutput 18 gauge 5 XIA5600INSTALLATION OutputConnections The lighting elements of DUAL illuminite speakers provide you with a unique custom touch to your vehicle. Dual's patent pending illuminite LED system and control circuitry provides an extraordinary blue-hue illumination which allows great creative opportunities for the beginner and seasoned custom installer alike. DUAL XIA-series amplifiers provide a dedicated switched 12VDC output including independent fused protection (2 amp) specifically for use with illuminite speakers. The first is labeled audio input terminals and the second is labeled illuminite lighting inputs. The inputs are clearly marked with a label positioned directly above the terminal housing. The polarity (+ and -) indicators for each set of inputs also appear on these labels. Do not connect the amplifier speaker outputs or any audio source to the illuminite lighting inputs. Make sure to observe polarity as the illuminite circuitry will not operate when connected reverse polarity. Connect either red wire from the XIA amplifier illuminite outputs to the positive (+) illuminite input terminal and connect either black wire from the XIA amplifier illuminite outputs to the negative (-) illuminite input. Additionalilluminitewiringnotes: Several illuminite speakers can be connected to the 12VDC illuminite output at one time. Refer to the table below for the individual illuminite speaker current requirements. If you are unsure, consult a qualified professional or call DUAL technical assistance at 1-866-382-5476 for further information. illuminitecurrent requirements (perspeaker) XiNC112 - 55mA XiNC110 - 55mA XiNBP210 - 180mA XiNBP212 - 180mA XOBP12D - 130mA OUTPUT CONNECTOR (Plugs into amplifier) 6 XIA5600INSTALLATION AmplifierConnections SpeakerConnections Connect speaker wires observing polarity. Use of loads lower than these is not recommended and may cause amplifier damage. The XIA5600 can be wired for stereo, bridged or stereo/bridged simultaneous operation. TypicalStereoWiring (2ohmsminimum) 2Speakers(stereo) Subwoofer(mono) TypicalBridgedWiring (4ohmsminimum) InputSignalConnections LowLevelInput(RCA) Low level (RCA) input signal is preferred for best performance. Typical trunk-mount amplifier installations require a 17-20 foot RCA cable. HighLevelInput(SpeakerWire) High level inputs should only be used when RCA outputs are not available from the head unit. [. . . ] Whatiscovered?This warranty covers all defects in material and workmanship in this product. The following are not covered: installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. Before you call for service, check the troubleshooting guide in your owner's manual. A slight adjustment of any custom controls may save you a service call. [. . . ]