User manual DRAYTEK VIGOR 2130 V1.2

[. . . ] Vigor2130 Series High Speed Gigabit Router User's Guide Version: 1. 2 Firmware Version: V1. 3. 0. 1 Date: 29/04/2010 ii Vigor2130 Series User's Guide Copyright Information Copyright Declarations Copyright 2010 All rights reserved. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp. Windows, Windows 95, 98, Me, NT, 2000, XP, Vista and Explorer are trademarks of Microsoft Corp. [. . . ] After installation, click on the Router Tools>>Syslog from program menu. 3. From the Syslog screen, select the router you want to monitor. Be reminded that in Network Information, select the network adapter used to connect to the router. Otherwise, you won't succeed in retrieving information from the router. Vigor2130 Series User's Guide 105 3. 10. 6 Time and Date It allows you to specify where the time of the router should be inquired from. Current System Time Time Zone Add NTP server Delete Click OK to save these settings. Click Inquire Time to get the current time. Click this button to remove an NTP server. 106 Vigor2130 Series User's Guide 3. 10. 7 Management This page allows you to manage the settings for access control, access list, port setup, and SMP setup. For example, as to management access control, the port number is used to send/receive SIP message for building a session. The default value is 5060 and this must match with the peer Registrar when making VoIP calls. Enable HTTP/HTTPS/SSH/ICMP Ping/FTP/TELNET Enable the checkbox to allow system administrators to login from the Internet. There are several servers provided by the system to allow you managing the router from Internet. Manager Host IP ­ Set one host as the manager to execute SNMP function. Type the IP address to specify the certain host. Enable SNMP Access List You could specify that the system administrator can only login from a specific host or network defined in the list. Subnet Mask - Represent a subnet mask allowed to login to the router. Vigor2130 Series User's Guide 107 3. 10. 8 Reboot System The Web Configurator may be used to restart your router for using current configuration. Click Reboot System from System Maintenance to open the following page. Click OK. Note: When the system pops up Reboot System web page after you configure web settings, please click OK to reboot your router for ensuring normal operation and preventing unexpected errors of the router in the future. 3. 10. 9 Firmware Upgrade Before upgrading your router firmware, you need to install the Router Tools. The following web page will guide you to upgrade firmware by using an example. Download the newest firmware from DrayTek's web site or FTP site. The DrayTek web site is www. draytek. com (or local DrayTek's web site) and FTP site is ftp. draytek. com. Click Maintenance>> Firmware Upgrade to launch the Firmware Upgrade Utility. Click Browse. . During the process of upgrade, do not turn off your router. 108 Vigor2130 Series User's Guide 4 Admin Mode Operation This chapter will guide users to execute advanced (full) configuration through admin mode operation. Please type "admin/admin" on Username/Password for administration operation. Now, the Main Screen will appear. Be aware that "Admin mode" will be displayed on the bottom left side. 4. 1 WAN Quick Start Wizard offers user an easy method to quick setup the connection mode for the router. Moreover, if you want to adjust more settings for different WAN modes, please go to Internet Access group. Basics of Internet Protocol (IP) Network IP means Internet Protocol. Every device in an IP-based Network including routers, print server, and host PCs, needs an IP address to identify its location on the network. To avoid address conflicts, IP addresses are publicly registered with the Network Information Centre (NIC). [. . . ] Type command (for Windows 95/98/ME) or cmd (for Windows NT/ 2000/XP/Vista). If the link is OK, the line of "Reply from 192. 168. 1. 1:bytes=32 time<1ms TTL=255" will appear. If the line does not appear, please check the IP address setting of your computer. For MacOs (Terminal) 1. If the link is OK, the line of "64 bytes from 192. 168. 1. 1: icmp_seq=0 ttl=255 time=xxxx ms" will appear. 226 Vigor2130 Series User's Guide 5. 4 Checking If the ISP Settings are OK or Not Open WAN>>Internet Access page and then check whether the ISP settings are set correctly. [. . . ]