User manual DOD SR835

[. . . ] All other servicing should be referred to qualified service personnel. For units equipped with externally accessible fuse receptacle: Replace fuse with same type and rating only. U. K. Mains Plug Warning A molded mains plug that has been cut off from the cord is unsafe. Never under any circumstances should you insert a damaged or cut mains plug into a 13 amp power socket. [. . . ] Frequency - This knob sets the crossover frequency separating the mids from the highs in Mono mode, and the lows from the highs for Channel 2 in Stereo mode. Range Switch - When depressed, this switch will multiply the selected crossover frequency by 10. The LED will light indicating that the markings on the Frequency knob (11) should be multiplied by 10. SR835 Crossover REAR PANEL WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. WARNING: SHOCK HAZARD-DO NOT OPEN AVIS: RISQUE DE CHOC ÉLECTRIQUE-NE PAS OUVRIR 120 V 100 V 60 Hz OR 50 Hz 3 HIGH BAL. HIGH UNBAL. LOW BAL. LOW UNBAL. STEREO INPUT LOW SUM OUT HIGH BAL. HIGH UNBAL. LOW BAL. LOW UNBAL. STEREO INPUT CHANNEL 2 CHANNEL 1 DOD Professional Products Sandy, Utah U. S. A. MONO HIGH BAL. HIGH UNBAL. MID BAL. MID UNBAL. MONO LOW BAL. LOW UNBAL. 18 WATTS 1 2 3 4 5 6 7 8 9 10 11 12 1. High Bal - This is a TRS balanced output for the high frequencies in both Mono mode and Channel 2 in Stereo mode. High Unbal - This is an unbalanced out put for the high frequencies in both Mono mode and Channel 2 in Stereo mode. Low/Mid Bal - This is a TRS balanced low frequency output for Channel 2 in Stereo mode and a TRS balanced mid range frequency output in Mono mode. Low/Mid Unbal - This is an unbalanced low frequency output for Channel 2 in Stereo mode and an unbalanced mid range frequency output in Mono mode. Channel 2 Input - This is a TRS balanced input for Channel 2 in stereo mode. Low Sum Output - This is a mono output containing the sum of Channel 1 and Channel 2 low frequencies. High Bal - This is a TRS balanced high frequency output for Channel 1 in Stereo mode. This jack has no function in Mono mode. High Unbal - This is an unbalanced high frequency output for Channel 1 in Stereo mode. This jack has no function in Mono mode. Low Bal - This is a TRS balanced low frequency output in both Mono mode and Channel 1 in Stereo mode. Low Bal - This is an unbalanced low frequency output in both Mono mode and Channel 1 in Stereo mode. Channel 1 Input - This is a TRS balanced input for Channel 1 in stereo mode and the master input in mono mode. Power Receptacle - Connect the provided power cord from this receptacle to an AC outlet. 4 SR835 Crossover INSTALLATION Install the crossover in a rack with the provided rack screws. Route the AC power cord to a convenient power outlet away from audio lines. Since the units draw a relatively small amount of current during idle, they can be left on continuously. DOD crossovers generate very little heat during operation and thus do not need to be specially ventilated or cooled. The units should not, however, be subjected to high temperatures for extended periods. Although the unit's chassis is shielded against radio frequency and electromagnetic interference, extremely high RF and EMI fields should be avoided. ATTENTION: Use only one Channel output connector for each frequency range at a time. Using the balanced and unbalanced outputs for the same frequency range at the same time can unbalance balanced lines, cause phase cancellation, short a conductor to ground, or cause damage to other equipment connected to the crossover. [. . . ] DOD Electronics liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned through the original dealer, where all parts and labor will be covered up to a period of three (3) years. The company shall not be responsible for any consequential damage as a result of the products use in any circuit or assembly. Proof of date of purchase is considered to be the burden of the consumer. DOD reserves the right to make changes in design or make improvements upon this product without incurring any obligation to install the same on PRODUCTS PREVIOUSLY MANUFACTURED. [. . . ]