User manual DIRT DEVIL TURBINE POWERHEAD

[. . . ] Turbine Powerhead Operating Instructions This Turbine Powerhead has been engineered for higher performance, quieter operation and superior cleaning ability. It has been carefully designed and manufactured for long life, reliable performance and convenient cleaning. It requires no electricity because it runs off the airflow of your central vacuum system. [. . . ] To release wand from the vertical locked position, gently place foot on Powerhead, grasp wand and pull back. Page 2 Use & Care of Your Turbine Powerhead (B) OPERATING PROCEDURES Your Turbine Powerhead runs off the airflow of your vacuum system. Whenever it is attached to an operating vacuum system, it will be running. No adjustments to the powerhead are necessary for different types of carpeting. To ensure maximum efficiency of the Turbine Powerhead, make sure that any filters, bags and cleaning hoses in your vacuum system are clean and free of blockage. The vacuum system is designed for dry pick up only. (C) CLEANING ROLLER BRUSH Turn off vacuum system and disconnect Powerhead. Threads, string, carpet fiber, fuzz and similar items may become wound around the beater brush. These should be removed by unwinding them by hand or carefully cutting with scissors. Keeping the beater brush clean will maintain efficiency. Page 3 Use & Care of Your Turbine Powerhead (D) REMOVING CLOGS Follow these steps if the turbine becomes obstructed: 1. Remove the clear belt cover by turning the Powerhead over and rotating the two latches until they align with the openings in the belt cover. Ensure the orange seal on the belt cover and mating surfaces are clean before reinstalling the belt cover. To reinstall the belt cover, simply insert the front of the belt cover under the baseplate edge and lower into its original position. Secure the belt cover in place by turning the two latches to the locked position. Turn latches to remove Belt Cover Remove Belt Cover Like This Remove clog here. Baseplate Edge Page 4 Use & Care of Your Turbine Powerhead (E) REPLACING THE DRIVE BELT It is recommended that the drive belt be replaced by a Qualified Service Technician. Place the new belt over one end, onto the brush roller, between the two center flanges. Slide the brush/belt assembly back into the housing recesses so the supports seat properly into the housing. [. . . ] THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY, AND H-P PRODUCTS, INC. SPECIFICALLY DISCLAIMS RESPONSIBILITY FOR CONSEQUENTIAL AND INCIDENTAL DAMAGES, AND LIMITS THE IMPLIED WARRANTY OF MERCHANTABILITY TO THE PERIOD OF EFFECTIVENESS OF THIS EXPRESS WARRANTY. (330) 875-5556 Page 6 Brush Bounces in Use Brush Hard to Push REPLACEMENT PARTS # 1 2 3 4 5 6 7 8 9 10 11 12 13 Description Lower Housing Wheel Assembly (2) Turbine Assembly Belt Cover Base Plate Compression Spring Washer, Spring Washer, Neck Neck Assembly Spring, Neck Lock Top Housing Seal, Small Roller Brush Assembly Part # 8412* 8425* 8558 8413 8414* 8557 5974 5971 8423 7218 8411* 7223 8457 # Description Part # 7226 8439 7228 7230 8556 7231 8428 8561 7238 7239 8416 8417 8427 8458 7224 14 T-Latch (2) 15 Belt 16 Screw, Housing (12) 17 Screw, T-Latch (2) 18 Bearing, Idler Assembly 19 Bushing, Wheel (2) 20 Shaft Support Assembly, Left 21 Shaft Support, Right, with washer 22 Ballast (2) 23 Foam Pad (4) 24 Shaft, Roller Wheel (2) 25 Roller Wheel (2) 26 Bearing Isolator (2) 27 Retaining Ring (2) 28 Seal, Belt Guard, Large * Please specify color when ordering. Page 7 p/n 8429 [. . . ]