User manual DIRECTV DSHD800

[. . . ] Use the keypad (0 ~ 9) to directly tune a channel (e. g. , 206). Press Prev CH once to return to the the last channel viewed. Press Alt Audio once to switch between English and a foreign language (e. g. , Spanish) if alternate audio is avaialble. Use Setup for all programming sequences. 6 TiVo Key Charts NOTE: On DIRECTV Receivers with TiVo service, several remote control keys function differently than those listed in the previous section. They are described below: Press to display program options (TiVo Central). [. . . ] Press and hold Setup until the DIRECTV key blinks twice, then release Setup. Use the Setup Codes for DIRECTV Receivers (on the next page) to locate the brand name and code for your specific DIRECTV Receiver. If performed correctly, the DIRECTV key will blink twice. NOTE: If the DIRECTV key emits a long blink, the code is invalid. Repeat steps 3 and 4 and try entering the same code again. 4. 5. Aim the DIRECTV universal remote control at the DIRECTV Receiver and press Power once. If it does not, repeat steps 3 and 4, trying each code for your brand until you find one that works. For future reference, write down the working DIRECTV code in the following box: DIRECTV CODE 6. 9 continued on next page. . . ABOUT DIRECTV CONTROL (continued) Setup Codes for DIRECTV Receivers: Hughes Network Systems (most models) Hughes Network Systems models GAEB0 and GCEB0 GE models GRD33G2A and GRD33G3A GE model GRD122GW Hitachi model HDS210R Mitsubishi HD models SRHD400 and SRHD500 Panansonic models TZ-DBS01 and TZ-DRD100 Panasonic models TUIRD10 and TUIRD20 Philips models DSX5150R, DSX5250R/I, DSX5350R, DSX5353R, and DSX5375R Philips HD model DSHD800R Proscan model PRD8630A Proscan model PRD8560B RCA models DRD102RW and DRD203RW RCA models DRD301RA, DRD302RA, DRD303RA, DRD403RA, and DRD703RA RCA models DRD502RB, DRD503RB, DRD505RB, DRD515RB, DRD523RB, and DRD705RB RCA models DRD202RD, DRD221RD, DRD222RD, DRD223RD, DRD225RD, DRD420RE, DRD440RE, DRD460RE, DRD480RE, DRD430RG, DRD450RG, and DRD485RG Samsung model SIR-S60W Sony models SAT-A1 and SAT-B1 Sony models SAT-A2 and SAT-B2 Sony models SAT-A3, SAT B3, SAT-A4, and SAT-B4 Sony models SAT-A50, SAT-A55 SAT-B50, and SAT-B55 Uniden model UDS100 0749 1749 0566 0866 0819 0749 0247 0701 1076 0749 0566 0766 0866 0566 0766 0392 1109 0639 0739 0839 0939 0724 Setup Codes for DIRECTV Personal Video Recorders (PVRs): Hughes Net. Sys. /TiVo model GXCEBOT Philips/TiVo model DSR6000R Sony/TiVo model SAT-T60 1142 (program under DIRECTV mode) 1142 (program under DIRECTV mode) 1639 (program under DIRECTV mode) 10 PROGRAMMING OTHER DEVICE CONTROL The DIRECTV universal remote control is also preprogrammed to operate an RCA TV, an RCA VCR, and a Pioneer audio Receiver. To control devices other than the default brands, perform the following steps; otherwise skip this section: NOTE: To control a DVD/PVR player, program the VCR key. For TV/VCR Combo control, skip this section and perform the instructions on the next page. 1. Turn on a device and, if applicable, insert a video cassette or DVD. NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. 2. On the DIRECTV universal remote control, press the device key you wish to program once (e. g. , TV, VCR, or AUX). Press and hold Setup until the selected device key blinks twice and then release Setup. Press and hold Power for 3 seconds to activate the Master Power feature. Thereafter, your DIRECTV universal remote control will sequentially turn on or off all of your home entertainment devices. Depending on what mode is currently selected, the DIRECTV universal remote control will send IR commands to the devices in this order: Start Mode DIRECTV TV VCR AUX Device On/Off TV, VCR, AUX End Mode DIRECTV VCR, AUX, DIRECTV DIRECTV AUX, DIRECTV, TV DIRECTV, TV, VCR DIRECTV DIRECTV For example, if TV is selected, pressing and holding Power for 3 seconds will first turn on (or off) the TV, then the VCR, then the auxiliary device, and finally the DIRECTV Receiver. NOTE: The DIRECTV universal remote control always defaults to the DIRECTV mode after all devices are turned off. Therefore, the initial power-on settings will always be DIRECTV, TV, VCR, and AUX, with the remote control returning to the DIRECTV mode as long as no other device key is pressed first. 25 RE-ASSIGNING DEVICE KEYS The DIRECTV universal remote control can be set up to control a second TV or VCR, or any combination of up to four home entertainment devices. For example, to have the DIRECTV universal remote control a TV, a DIRECTV Receiver, and two VCRs, you will need to re-assign the unused AUX key to operate the second VCR as follows: 1. Then press and hold Setup until the AUX key blinks twice, then release Setup. See Programming Other Device Control on page 11. To re-assign other device keys, repeat steps 1 to 4 and substitute the key sequence using the following chart: To Re-Assign VCR as 2nd TV key: Perform Key Sequence Setup - 9 - 9 - 2 - TV - VCR VCR as 2nd AUX key: Setup - 9 - 9 - 2 - AUX - VCR VCR as 2nd DIRECTV key: VCR back to VCR: AUX as 2nd TV key: AUX as 2nd VCR key: AUX as 2nd DIRECTV key: AUX back to AUX: Setup - 9 - 9 - 2 - DIRECTV - VCR Setup - 9 - 9 - 2 - VCR - VCR Setup - 9 - 9 - 2 - TV - AUX Setup - 9 - 9 - 2 - VCR - AUX Setup - 9 - 9 - 2 - DIRECTV - AUX Setup - 9 - 9 - 2 - AUX - AUX Upon completion of a re-assignment, the selected mode key will blink twice to confirm your selection. Then, you'll need to program device control (see Programming Other Device Control on page 11). 26 CHANGING VOLUME LOCK The DIRECTV universal remote control is set to control volume of a device through your TV while in the TV, VCR, or DIRECTV mode. However, in the AUX mode, you still have separate control of of your auxilary device's volume. If your TV is not remote controllable, or if you would like the volume to be controlled by a different device, you can change the Volume Lock setting to control a volume through a non-associated mode (e. g. , through the VCR in the TV mode). To Change Volume Lock To The VCR Mode: 1. Then press and hold Setup until the VCR key blinks twice, then release Setup. Now, whenever you press Volume or Mute, volume will be controlled by your VCR. To Change Volume Lock To The DIRECTV Mode: 1. [. . . ] You are a customer of DIRECTV and your account is in good standing; and b. The problem with the DIRECTV universal remote control was not caused by abuse, mishandling, alteration, accident, failure to follow operating, maintenance or environmental instructions set forth in this User Guide, or service performed by someone other than DIRECTV. THE DIRECTV DSHD800 IS PROVIDED ON AN AS IS, AS AVAILABLE BASIS, SOLELY FOR YOUR NON-COMMERCIAL, RESIDENTIAL USE. DIRECTV DOES NOT MAKE ANY REPRESENTATIONS OR WARRANTIES OF ANY KIND, WHETHER STATUTORY, EXPRESS OR IMPLIED, REGARDING THE DIRECTV DSHD800, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, NONINFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE OR IMPLIED WARRANTIES ARISING FROM A COURSE OF DEALING OR COURSE OF PERFORMANCE. [. . . ]