User manual DIALON F20

[. . . ] Cordless DECT telephone Schnurloses DECT Telefon · Telefono senza filo digitale DECT Téléphone DECT sans fil · Telefónico DECT inalámbrico Operating Manual and Safety Precautions Brief overview handset Display Shows in second row e. g. N time (left) N handset number (centre) N date (right) Earpiece NAVIGATION key Scroll options PHONE BOOK key Access to phone book MENU key N Access to settings N Switch OFF the microphone during a call (mute) REDIAL key / CALLER LIST key N Access the last five dialled numbers R key N Flash time settings N Access the Caller list N Insert a pause TALK key N Accept call N Dial number N Select a menu entry END CALL key N End a call / reject a call N Cancel a menu entry N Activate/deactivate keypad lock * key Start a conference call (3-way conversation) N Switch handset OFF/ON INT key / # key N Start an internal call N Toggle between internal and external call Microphone Base station LED Lights up during an external call PAGING key N Search all handsets N Register handsets Quick guide to handset display icons © Ú SIGNAL STRENGTH icon (blinking when no signal or the signal strength is weak) INT INTERNAL CALL icon DO NOT DISTURB (handset ringer muted) CALLER LIST active (icon is blinking when a new call is in the Caller list) PHONE BOOK active REDIAL LIST active KEYPAD LOCK active CHARGING STATUS icon (U full; = flat; blinking during charging) MICROPHONE MUTE indicator (in second row) External call without Calling Line Identification Presentation (CLIP; in second row) Û Þ U Ø â åååå æ 2 Contents Brief overview handset . 8 3 Safety instructions guide are available in all countries. ! N When the keypad is locked (see page 8) emergency numbers cannot be dialled either. Putting the telephone into service Step 1: Connecting the base station Connect your base station to the telephone socket and the mains socket: Telephone socket * Mains socket (AC 230 V, 50 Hz) N Not all the functions described in this user Use only the plug-in power supply unit provided. Never use conventional (non-rechargeable) batteries, since these can injure you and damage your health. [. . . ] If the internal user does not answer, the call automatically returns after 30 seconds waiting time. Enter the internal call number. interconnect the 3-way conversation. P Press longer than one second to Note: During the conversation, the INT icon is blinking. a Press to forward the call. R Press longer than one second to Internal enquiry / toggling You are conducting a call with an external user. You can call an other internal user to conduct an enquiry call without clearing down the initial connection. You are automatically reconnected to the external connection when you end the enquiry call. nected to the internal user. toggle between the internal and the external connection. Note: The INT icon is ON when con- a Press to end the external call. Note: The handset switches to the idle state. The external user remains connected to the other internal user. 10 You can also use the , , barge-in" function for a 3-way conversation. However, in this case care must be taken about the privacy of a call. View and change settings All settings both for the handset and the base station are made at the handset. Call waiting during an internal call You are conducting an internal call and hear a CALL WAITING tone that signals an additional external call. To accept the waiting call you have two possibilities: Entering HANDSET SETUP or BASE SETUP menu i Press to enter the menu. SETUP menu or . . . 1 Press to enter the HANDSET S Press to end the first connection. or . . . 2 press to enter the BASE SETUP menu. ~ R Press longer than one second to put the first user on hold. If required, enter the correct handset PIN or base station PIN (4 digits). Note: The factory setting of the PIN is 0000. If you do not change this setting, you enter directly the HANDSET SETUP or BASE SETUP menu. If the PIN does not match, the handset returns to the idle state. R If the first user is put on hold, press nected to the internal user and blinking when connected to the external user. longer than one second to toggle between the two connections. Note: The INT icon is ON when con- Menu navigation ~ Type in the number of the next menu entry. You will find a menu overview on page 19. c Press to confirm an entry or operation. Note: After confirmation of a setting you are still in the menu. This allows you to directly make further settings. q Select a setting. a Press to return to the idle display after confirmation of a setting or . . . a press to cancel the last entry or last operation. Note: If you press longer than one second the handset returns to the idle display without saving the setting. 11 HANDSET SETUP menu Set handset ringer volume You can choose from four ringer volumes: Set earpiece volume You can choose from three earpiece volumes: i Press. q Select the earpiece volume (see table below). ~ If necessary, enter handset PIN. If necessary, enter handset PIN. q Select the ringer volume (see table c Press to confirm. Display shows P :H 11 0 P :H 11 P :H 11 P :H 11 1 2 3 Volume setting Ringer OFF (display shows Ú) LOW MEDIUM HIGH c Press to confirm. Display P :H 13 P :H 13 P :H 13 shows 1 2 3 Volume setting LOW MEDIUM HIGH Set handset ringer melody You can choose from three melodies: Adjust temporarily earpiece volume You can select temporarily three earpiece volumes while making a call: q Adjust the volume. A number (1 to 3) shows the volume on the handset display. i Press. q Select the ringer melody (see table below). ~ If necessary, enter handset PIN. Switch key beep ON/OFF i Press. q Select KEY BEEP ON or OFF (see table below). ~ 2 Press. If necessary, enter handset PIN. c Press to confirm. Display shows P :H 12 1 P :H 12 2 P :H 12 3 Melody MELODY 1 MELODY 2 MELODY 3 c Press to confirm. Display shows P :H 14 0 P :H 14 1 KEY BEEP OFF ON 12 Three different key beeps indicate key pressing and error or success of an operation. Beep KEY (short beep) ERROR (beep followed by two short beeps) SUCCESS (beep followed by a longer beep) Meaning Key pressing Unavailable selection or unsuccessfull function Successfull confirmation of function Setting at the Dialon F20 base station Make sure that the base station is connected correctly (step 1, see page 4) and the batteries are inserted in the handset (step 2, see page 5). Press the PAGING key at the base station until you will hear the registration tone (continuous beeps). Settings at the handset To register the Dialon F20 handset at the Dialon F20 base station: Activate/deactivate auto talk mode When this function is activated, you can remove the handset from the charging unit without pressing c to accept a call (factory setting). i Press. 1 Press. ~ If necessary, enter handset PIN. If necessary, enter handset PIN. 2 Press. q Activate/deactivate AUTO TALK MODE (see table below). Enter the base station PIN (4 digits; factory setting is 0000). Note: If you register your handset at a base station of an other manufacturer, it may be necessary to enter up to 8 numeric digits. Please refer to the operating instructions of this base station. c Press to confirm. Display shows P :H 2 0 P :H 2 1 AUTO TALK MODE OFF ON (factory setting) c Press. [. . . ] In many cases, you will then be able to use it again. No reaction to keystroke. No radio connection to the base station: © blinking! Troubleshooting guide What to do, if you forgot the handset PIN?N Plug in mains power supply and simultaneously press the PAGING key at the base station until you will hear a beep. N Then register all handsets new (see page 13). Charge the battery for 15 hours (see page 5). [. . . ]