User manual DFI GF9400 T2RS

[. . . ] System Board User's Manual Copyright This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders. The manufacturer makes no representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose. The user will assume the entire risk of the use or the results of the use of this document. [. . . ] System BIOS Cacheable When this field is enabled, accesses to the system BIOS ROM addressed at F0000H-FFFFFH are cached, provided that the cache controller is enabled. The larger the range of the Cache RAM, the higher the efficiency of the system. 3 63 3 BIOS Setup Integrated Peripherals Phoenix - AwardBIOS CMOS Setup Utility Integrated Peripherals IDE Function Setup MCP Storage Config Onboard Superio Device HD Audio MAC Lan MAC Media Interface USB Device Setting Press Enter Press Enter Press Enter INT Codec * EXT Codec Auto RGMII Press Enter Item Help Menu Level : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults The settings on the screen are for reference only. Your version may not be identical to this one. IDE Function Setup MCP Storage Config Onboard Superio Device HD Audio The options are Disabled, Internal Codec, External Codec and INT Codec + EXT Codec. USB Device Setting Refer to the following pages for more information on this submenu. Refer to the following pages for more information on these submenus 64 BIOS Setup IDE Function Setup Phoenix - AwardBIOS CMOS Setup Utility IDE Function Setup IDE DMA Transfer Access IDE Prefetch Mode IDE HDD Block Mode Enabled Enabled Enabled Item Help Menu Level 3 : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults The settings on the screen are for reference only. Your version may not be identical to this one. IDE DMA Transfer Access This field is used to enable or disable the DMA transfer function of an IDE hard drive. IDE Prefetch Mode This allows data and addresses to be stored in the internal buffer of the chip, thus reducing access time. The system BIOS will check the hard disk drive for the maximum block read/write per sector the system can transfer. The IDE HDD uses the standard mode. Disabled 65 3 BIOS Setup MCP Storage Config Phoenix - AwardBIOS CMOS Setup Utility Onboard PCI Device Serial-ATA Controller SATA Operation Mode Enabled IDE Item Help Menu Level : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults The settings on the screen are for reference only. Your version may not be identical to this one. Serial-ATA Controller This field is used to enable or disable the Serial ATA controller. IDE RAID AHCI Linux AHCI This option configures the Serial ATA drives as Parallel ATA storage devices. This option allows you to create RAID configuration on Serial ATA devices. This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Interface). This option allows the Serial ATA devices to use Linux AHCI. 66 BIOS Setup Onboard Super IO Device Phoenix - AwardBIOS CMOS Setup Utility Onboard Super IO Device Power On Function x KB Power On Password x Hot Key Power On Onboard FDC Controller Onboard Serial Port Onboard IRDA Select x IR Mode Select x UR2 Duplex Mode PWRON After PWR-Fail Button Only Enter Ctrl-F1 Enabled 3F8/IRQ4 Disabled IrDA Half Off Item Help Menu Level 3 : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults The settings on the screen are for reference only. Your version may not be identical to this one. Power On Function This field allows you to use the keyboard or PS/2 mouse to poweron the system. When this option is selected, set the password you would like to use to power-on the system in the "KB Power On Password" field. When this option is selected, select the function key you would like to use to power-on the system in the "Hot Key Power On" field. When this option is selected, press the "wake up" key of the Windows 98 compatible keyboard to power-on the system. Hot Key Mouse Move Mouse Click Any Key Keyboard 98 67 3 BIOS Setup KB Power On Password Move the cursor to this field and press <Enter>. Type in exactly the same password to confirm, then press <Enter>. The power button will not function once a keyboard password has been set in this field. If you forgot the password, power-off the system and remove the battery. Wait for a few seconds and install it back before powering-on the system. [. . . ] Check the jumper settings to ensure that the jumpers are properly set. Verify that all memory modules are seated securely into the memory sockets. If the board fails to function, place the board on a flat surface and seat all socketed components. If you made changes to the BIOS settings, re-enter setup and load the BIOS defaults. 133 C 134 Possible Cause 1. [. . . ]