User manual DEVILLE C07367 02-07

[. . . ] Fixer l'ensemble écran de mur + écran de plafond au mur en utilisant les 6 vis, chevilles et rondelles, livrées dans le sachet notice et en respectant une distance de 60 mm entre le plafond et l'écran de plafond (Fig. 2 - Type and dimensional characteristics of the chimney flue to which the fireplace must beconnected. We strongly recommend that you take the time to thoroughly read and familiarize yourself with this manual in order to obtain maximum enjoyment and satisfaction from your DEVILLE fireplace. All local, national, and european regulations must be respected when using this appliance. [. . . ] Secure the wall + ceiling shield assembly fitted with the rectangular knockout (4 self-tapping screws supplied in the instruction packet ; this operation is performed when the floor to ceiling height is greater than 2. Secure the tube cover shield to the hood shield using the self-tapping screws supplied in the instruction packet · Fit the upper tube cover into the lower tube cover and adjust to dimension H. 2 holes in the upper tube cover through the 4 holes located in the upper section of the lower tube cover. assemble the 2 tube covers with the 4 selftapping screws included in the instruction packet. Spread apart the assembly made of the 2 tube covers and fit the hood onto the fireplace. Secure this assembly onto the hood using 4 selftapping screws, included in the instruction packet. 2 installation configurations are possible : In both cases, the ceiling shield is placed 60 mm from the ceiling. CONNECTION ON TOP (FIG 5) Remove the circular knockouts from the ceiling and tube cover shields (leave the others in place) (Fig. Secure the wall + ceiling shield assembly to the wall with the 6 screws, anchors and nuts included in the instruction packet while maintaining a distance of 60 mm between the ceiling and the ceiling shield (Fig. Secure the tube cover shield to the hood shield using the sheetmetal screws supplied in the instruction packet (Fig. 9) while maintaining a distance of 60 mm between the ceiling and the ceiling shield. Special case where the chimney flue penetrates into the room at a certain height and whose dimensions allow its integration into the upper tube cover (see Fig. However, it must be checked before setting the appliance into service. At an ambient temperature of 20° there must C, no gap between the mating face and the shutter when the operating handle is positioned on the 0 mark (when the appliance is cold) (Fig. The shutter must not be pushed, it should come free from the mating face as soon as the handle is turned to position 1. If necessary, operate the shutter adjusting mechanism by moving the adjusting knob inside the ash pan compartment. In this case, grease the operating screw (2) (with graphite grease or engine oil, etc. 1), have a moderate fire for the first hours and limit the loading of the appliance (a Ø 15 cm log) turning the control knob for the air on position 4 : this enables the temperature of all chimney elements to rise progressively and ensures normal fireplace dilation. The burning power given is the average burning power obtained with each 3 hours load. Slow combustion, autonomy greater than 10 hours in continuous use : · Obtained on a 6 Pa draft with a 14 kg-load composed of a non-split log of strong wood, preferably with large diameters (superior to 16 cm). Reload on a 0, 30 kg (that is to say 2 cm thick) ash lay with the thermostat on position 0 and the ventilation duct closed. Place some crumpled paper and very dry twigs on the grate followed by branches of larger diameter (approximately 3 to 5 cm). [. . . ] Remove the 3 mounting screws (1) from the fan support and the protective grille. TERMS AND CONDITIONS Apart from the legal warranty, particularly for latent defects, Deville guarantees to deliver the furniture in case of obvious defects or non-conformity to the ordered furniture. Without prejudice to the provisions that are to be taken concerning the carrier, claims on delivery of furniture concerning the obvious defects or the non conformity, must be issued by the Buyer in writing a registered letter with confirmation of receipt to Deville company with in 5 days after noticing the defect. It is up to the Buyer to prove the reality of the noticed defects and irregularities. [. . . ]