User manual DENON RCD-CX1

[. . . ] SUPER AUDIO CD RECEIVER RCD-CX1 Owner's Manual Bedienungsanleitung Manuel de l'Utilisateur Manuale delle istruzioni Manual del usuario Gebruiksaanwijzing Bruksanvisning ENGLISH DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA · DECLARATION OF CONFORMITY We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3. Following the provisions of 2006/95/EC and 2004/108/EC Directive. n SAFETY PRECAUTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION · ÜBEREINSTIMMUNGSERKLÄRUNG Wir erklären unter unserer Verantwortung, daß dieses Produkt, auf das sich diese Erklärung bezieht, den folgenden Standards entspricht: EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3. Entspricht den Verordnungen der Direktive 2006/95/EC und 2004/108/EC. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] If the protection circuit is activated though there are no problems in ventilation around the set or in connections, the set could be damaged. Turn off the power, then contact a DENON servicing and inquiry outlet. Getting Started 1 (L) (R) Peel off about 10 mm of sheathing from Connections the tip of the speaker cable, then either twist the core wire tightly or terminate it. the hilt into the speaker terminal. Setup w q w q 2 3 4 Turn Playback Insert the speaker cable's core wire to Setting the Timer Turn the speaker terminal clockwise to tighten it. NOTE · Use speakers with an impedance of 4 to 16 /ohms. The protection circuit may be activated if speakers with an impedance other than specified are used. · Connect the speaker cables in such a way that they do not stick out of the speaker terminals. The protection circuit may be activated if the core wires touch the rear panel or if the + and ­ sides touch each other (v "Protection circuit"). · Never touch the speaker terminals while the power supply is connected. Doing so could result in electric shock. Other Functions Troubleshooting Specifications ENGLISH Connecting the Playback Components Record Player iPod® Use a DENON control dock for iPod (ASD-1R or ASD-3N/3W, sold separately) to connect the iPod to the RCD-CX1. Connecting a Power Amp and Subwoofer Use when adding a power amp, subwoofer, etc. Power amp / Subwoofer Getting Started Connections Setup Playback Setting the Timer Other Functions Troubleshooting Specifications iPod Turntable L R L R L R L R L R NOTE · With some record players, noise may be generated when the ground wire is connected. · Set the CARTRIDGE selection switch to "jMM" or "hMC" according to the cartridge being used. · When using a control dock for iPod, the Control Dock for iPod must be set. For details, refer to the operating instructions of the Control Dock for iPod. · When the control dock for iPod is connected, the function indicator switches from "LINE1" to "iPod". · To use an iPod, see "iPod® Playback" (vpage 22). DO NOT insert a short pin plug for recording output (REC) and pre-out terminals, as this may result in damage. NOTE The RCD-CX1's SIGNAL GND terminal is meant to reduce noise when a record player is connected. This is not a safety ground terminal. 0 ENGLISH Connecting the Recording Components CD Recorder / MD Recorder / Tape Deck Analog connections CD recorder / MD recorder / Tape deck Digital connections CD recorder / MD recorder n When connecting the optical digital output connector with an optical transmission cable (sold separately) Getting Started Connections Protective cap Match the shapes Remove the protective cap, match the shapes, then insert firmly all the way in. Setup Store the protective cap in a safe place so as not to lose it, and use it when not using the terminal. Playback Setting the Timer L R L R L R L R Other Functions Troubleshooting No digital signals are output for Super Audio CDs. Specifications ENGLISH Connections to Other Devices Antenna terminals AM / FM The AM and FM reception sensitivity depends on the place the antenna is set and the direction in which it is set. AM loop antenna (supplied) Connecting the Power Cord Wait until all connections have been completed before connecting the power cord. Getting Started Connections Setup Playback Setting the Timer Other Functions Troubleshooting Specifications To household power outlet (AC 230 V, 50 Hz) FM indoor antenna (supplied) Power cord (supplied) NOTE · Insert the AC plugs securely. · When the power cord is plugged into the power outlet, the power indicator flashes orange for about 10 seconds. Do not unplug the power cord before the power indicator turns off and the RCD-CX1 enters Standby mode. · Be sure the power cord is unplugged from the power outlet before connecting or disconnecting it to the AC IN. Once Connections are Completed n Connecting the AM loop antenna 1 2 3 Turning the Power On (vpage 14) Push the lever. Insert the conductor. Return the lever. NOTE · Make sure the AM loop antenna lead terminals do not touch metal parts of the panel. · Do not connect two FM antennas simultaneously. ENGLISH Getting Started Setup Symbols used to indicate buttons in this manual Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] Setting the Current Time (24-Hour Display) GExampleH Setting the current time to 10:15 am n Checking the current time when the power is on Press and hold in [TIME/DISPLAY]. [. . . ] · The set's remote control sensor is exposed to strong light (direct sunlight, inverter type fluorescent bulb light, etc. ). · Insert the batteries in the proper direction, following the polarity marks in the battery compartment. · Move the set to a place in which the remote control sensor will not be exposed to strong light. Page 4 4 4 4 4 No sound is produced from one side. For stereo sources, the positions of the instruments are inverted. · The speaker cables are not · Connect securely. [. . . ]